OM7580SC datasheet(2/4 Pages) IRF

2 / 4 page

www.irf.com

OM7580SC

Footnotes

Q- Denotes specifications which apply over the full operating temperature range.

R- The minimum load current is minimum current required to maintain regulation. Normally the current in

the resistor divider used to set the output voltage is selected to meet the minimum load current

requirement.

S- The control pin current is the drive current required for the output transistor. The control pin current is

approximately 0.01% output current. The minimum value is equal to quiescent current of the device.

Electrical Characteristics @TA = 25°C (Unless Otherwise Specified)

Parameter

Test Conditions

Min. Typ. Max. Units

Reference Voltage

VCTRL = 2.7V, VPWR = 2.0V, ILOAD = 10mA

1.243 1.250 1.257

VADJ= 0V

VCTRL=2.7 to 12V, VPWR=1.75V to 5.5V, ILOAD =10mA to 6.0A Q

1.237 1.250 1.263

Line Regulation

VCTRL = 2.5 to 12V, VPWR = 3.0V to 5.5V, ILOAD = 1.0mA Q

1.0

3.0

Load Regulation

VCTRL = 2.75V, VPWR = 2.1V, ILOAD = 10mA to 6.0A Q

1.0

5.0

Minimum Load Current VCTRL = 5.0V, VPWR = 3.3V, VADJ= 0V QR

5.0

Ground Pin Current

VCTRL = 5.0V, VPWR = 3.3V, ILOAD = 0mA Q

6.0

VCTRL= 2.75V, VPWR= 2.05V, ILOAD= 7.0A, TJ = 25°C

120

VCTRL= 2.75V, VPWR= 2.05V, ILOAD= 7.0A, TJ = 125°C

120

VCTRL= 2.75V, VPWR= 2.05V, ILOAD= 6.0A, TJ = -55°C

130

Adjust Pin Current

VCTRL= 2.75V, VPWR = 2.05V, ILOAD = 10mA

120

µA

VADJ= 0V

VCTRL = VPWR = 5.0V (AVG), VRIPPLE = 1.0VP-P, f= 120Hz

IOUT = 4.0A TJ = 25°C

VCTRL= 2.75V, VPWR= 2.05V, ∆VOUT = 100mV, TJ = 25°C

7.1

8.0

VCTRL=2.75V, VPWR=2.05V, ∆VOUT=100mV, TJ=-55°C & TJ=+125°C 6.6

VPWR = 3.3V, ILOAD = 7.0A, TJ = 25°C

1.33

VPWR = 3.3V, ILOAD = 7.0A, TJ = 125°C

1.33

VPWR = 3.3V, ILOAD = 6.0A, TJ = -55°C

1.35

VCTRL = 2.75V, ILOAD = 7.0A, TJ = 25°C

0.62

VCTRL = 2.75V, ILOAD = 7.0A, TJ = 125°C

0.80

VCTRL = 2.75V, ILOAD = 6.0A, TJ = -55°C

0.80

Thermal Regulation

VPWR = 5.0V, IO = 7.0A, PD ≥ 20W, pulse width = 30ms

0.02

%/W

Dropout is caused by either minimum control voltage or minimum power voltage. Both

Dropout Voltage

parameters are specified with respect to the output voltage. The specifications represent the

minimum input/output voltage required to maintain 1% regulation.

Minimum VCONTROL

Minimum VPWR

Ripple Rejection

Current Limit

Control Pin Current

OM7580SC 数据表(PDF) 2 Page - International Rectifier

OM7580SC 数据表(HTML) 2 Page - International Rectifier

Html Pages

1 2 3 4

数据表下载