335 datasheet(21/82 Pages) INTEL

21 / 82 page

Datasheet

Electrical Specifications

2.7

Asynchronous GTL+ Signals

Legacy input signals (such as A20M#, IGNNE#, INIT#, SMI#, SLP#, and STPCLK#) use CMOS

input buffers. All of these signals follow the same DC requirements as GTL+ signals; however, the

outputs are not actively driven high (during a logical 0-to-1 transition) by the processor. These

signals do not have setup or hold time specifications in relation to BCLK[1:0].

All of the Asynchronous GTL+ signals are required to be asserted/de-asserted for at least six

BCLKs for the processor to recognize the proper signal state. See Section 2.11 for the DC

specifications for the Asynchronous GTL+ signal groups. See Section 6.2 for additional timing

requirements for entering and leaving the low power states.

2.8

Test Access Port (TAP) Connection

Due to the voltage levels supported by other components in the Test Access Port (TAP) logic, it is

recommended that the Celeron D processor be first in the TAP chain and followed by any other

components within the system. A translation buffer should be used to connect to the rest of the

chain unless one of the other components is capable of accepting an input of the appropriate

voltage level. Similar considerations must be made for TCK, TMS, TRST#, TDI, and TDO. Two

copies of each signal may be required, with each driving a different voltage level.

Table 2-4. Signal Characteristics

Signals with R

Signals with no R

A[35:3]#, ADS#, ADSTB[1:0]#, AP[1:0]#, BINIT#,

BNR#, BOOTSELECT1, BPRI#, D[63:0]#, DBI[3:0]#,

DBSY#, DEFER#, DP[3:0]#, DRDY#, DSTBN[3:0]#,

DSTBP[3:0]#, HIT#, HITM#, LOCK#, MCERR#,

OPTIMIZED/COMPAT#1, PROCHOT#, REQ[4:0]#,

RS[2:0]#, RSP#, TRDY#

NOTES:

The OPTIMIZED/COMPAT# and BOOTSELECT pins have a 500–5000

Ω pull-up to V

CCVID rather than RTT.

A20M#, BCLK[1:0], BPM[5:0]#, BR0#, BSEL[1:0],

COMP[1:0], FERR#/PBE#, IERR#, IGNNE#, INIT#,

LINT0/INTR, LINT1/NMI, PWRGOOD, RESET#,

SKTOCC#, SLP#, SMI#, STPCLK#, TDO,

TESTHI[12:0], THERMDA, THERMDC,

THERMTRIP#, VID[5:0], VIDPWRGD,

GTLREF[3:0], TCK, TDI, TRST#, TMS

Open Drain Signals2

Signals that do not have RTT, nor are actively driven to their high-voltage level.

BSEL[1:0], VID[5:0], THERMTRIP#, FERR#/PBE#,

IERR#, BPM[5:0]#, BR0#, TDO

Table 2-5. Signal Reference Voltages

GTLREF

VCC/2

VCCVID/2

BPM[5:0]#, LINT0/INTR, LINT1/NMI, RESET#, BINIT#,

BNR#, HIT#, HITM#, MCERR#, PROCHOT#, BR0#,

A[35:0]#, ADS#, ADSTB[1:0]#, AP[1:0]#, BPRI#, D[63:0]#,

DBI[3:0]#, DBSY#, DEFER#, DP[3:0]#, DRDY#,

DSTBN[3:0]#, DSTBP[3:0]#, LOCK#, REQ[4:0]#, RS[2:0]#,

RSP#, TRDY#

A20M#, IGNNE#, INIT#,

PWRGOOD1, SLP#, SMI#,

STPCLK#, TCK1, TDI1,

TMS1, TRST#1

NOTES:

These signals also have hysteresis added to the reference voltage. See Table 2-12 for more information.

VIDPWRGD,

BOOTSELECT,

OPTIMIZED/

COMPAT#

335 数据表(PDF) 21 Page - Intel Corporation

335 数据表(HTML) 21 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

数据表下载