ST10F272Z2Q3 datasheet(63/189 Pages) STMICROELECTRONICS

63 / 189 page

ST10F272Z2

General purpose timer unit

63/189

11.2

GPT2

The GPT2 module provides precise event control and time measurement. It includes two

timers (T5, T6) and a capture/reload register (CAPREL). Both timers can be clocked with an

input clock which is derived from the CPU clock via a programmable prescaler or with

external signals. The count direction (up/down) for each timer is programmable by software

or may additionally be altered dynamically by an external signal on a port pin (TxEUD).

Concatenation of the timers is supported via the output toggle latch (T6OTL) of timer T6

which changes its state on each timer overflow/underflow.

The state of this latch may be used to clock timer T5, or it may be output on a port pin

(T6OUT). The overflow / underflow of timer T6 can additionally be used to clock the

CAPCOM timers T0 or T1, and to cause a reload from the CAPREL register. The CAPREL

corresponding port pin (CAPIN), and timer T5 may optionally be cleared after the capture

procedure. This allows absolute time differences to be measured or pulse multiplication to

be performed without software overhead.

The capture trigger (timer T5 to CAPREL) may also be generated upon transitions of GPT1

timer T3 inputs T3IN and/or T3EUD. This is advantageous when T3 operates in Incremental

Interface Mode.

Table 37 and Table 38 list the timer input frequencies, resolution and periods for each pre-

scaler option at 40 MHz and 64 MHz CPU clock respectively.

Table 37.

GPT2 timer input frequencies, resolutions and periods at 40 MHz

CPU = 40 MHz

Timer Input Selection T5I / T6I

000b

001b

010b

011b

100b

101b

110b

111b

Pre-scaler factor

128

256

512

Input Freq

10 MHz

5 MHz

2.5 MHz

1.25 MHz

625 kHz

312.5 kHz 156.25 kHz 78.125 kHz

Resolution

100 ns

200 ns

400 ns

0.8 µs

1.6 µs

3.2 µs

6.4 µs

12.8 µs

Period maximum

6.55 ms

13.1 ms

26.2 ms

52.4 ms

104.8 ms

209.7 ms

419.4 ms

838.9 ms

Table 38.

GPT2 timer input frequencies, resolutions and periods at 64 MHz

CPU = 64 MHz

Timer Input Selection T5I / T6I

000b

001b

010b

011b

100b

101b

110b

111b

Pre-scaler factor

128

256

512

Input Freq

16 MHz

8 MHz

4 MHz

2 MHz

1 kHz

500 kHz

250 kHz

128 kHz

Resolution

62.5 ns

125 ns

250 ns

0.5 µs

1.0 µs

2.0 µs

4.0 µs

8.0 µs

Period maximum

4.1 ms

8.2 ms

16.4 ms

32.8 ms

65.5 ms

131.1 ms

262.1 ms

524.3 ms

ST10F272Z2Q3 数据表(PDF) 63 Page - STMicroelectronics

ST10F272Z2Q3 数据表(HTML) 63 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载