71M6543F datasheet(21/157 Pages) MAXIM

21 / 157 page

71M6543F/H and 71M6543G/GH Data Sheet

v1.2

Figure 6: General Topology of a Chopped Amplifier

It is assumed that an offset voltage Voff appears at the positive amplifier input. With all switches, as

controlled by CROSS (an internal signal), in the A position, the output voltage is:

Voutp – Voutn = G (Vinp + Voff – Vinn) = G (Vinp – Vinn) + G Voff

With all switches set to the B position by applying the inverted CROSS signal, the output voltage is:

Voutn – Voutp = G (Vinn – Vinp + Voff) = G (Vinn – Vinp) + G Voff, or

Voutp – Voutn = G (Vinp – Vinn) - G Voff

Thus, when CROSS is toggled, e.g., after each multiplexer cycle, the offset alternately appears on the

output as positive and negative, which results in the offset effectively being eliminated, regardless of its

polarity or magnitude.

When CROSS is high, the connection of the amplifier input devices is reversed. This preserves the overall

polarity of that amplifier gain; it inverts its input offset. By alternately reversing the connection, the amplifier’s

offset is averaged to zero. This removes the most significant long-term drift mechanism in the voltage

reference. The CHOP_E[1:0] (I/O RAM 0x2106[3:2]) control field controls the behavior of CROSS. On the

first CK32 rising edge after the last multiplexer state of its sequence, the multiplexer waits one additional

CK32 cycle before beginning a new frame. At the beginning of this cycle, the value of CROSS is updated

according to the CHOP_E[1:0] field. The extra CK32 cycle allows time for the chopped VREF to settle.

During this cycle, MUXSYNC is held high. The leading edge of MUXSYNC initiates a pass through the CE

program sequence.

CHOP_E[1:0] has four states: positive, reverse, and two toggle states. In the positive state, CHOP_E[1:0]

= 01, CROSS is held low. In the reverse state, CHOP_E[1:0] = 10, CROSS is held high. The two

automatic toggling states are selected by setting CHOP_E=11 or CHOP_E=00.

Figure 7: CROSS Signal with CHOP_E = 00

Figure 7 shows CROSS over two accumulation intervals when CHOP_E[1:0] = 00: At the end of the

first interval, CROSS is high, at the end of the second interval, CROSS is low. Operation with

CHOP_E[1:0] = 00 does not require control of the chopping mechanism by the MPU.

In the second toggle state, CHOP_E[1:0] = 11, CROSS does not toggle at the end of the last multiplexer

cycle in an accumulation interval.

inp

outp

outn

inn

CROSS

71M6543F 数据表(PDF) 21 Page - Maxim Integrated Products

71M6543F 数据表(HTML) 21 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载