PCA9561_04 datasheet(5/17 Pages) PHILIPS

5 / 17 page

Philips Semiconductors

Product data sheet

PCA9561

Quad 6-bit multiplexed I2C EEPROM DIP switch

2004 May 17

If the command byte is an EEPROM address, the next byte sent will be programmed into that EEPROM address on the following STOP

condition, if the WP is logic 0. If more than one byte is sent sequentially, the second byte will be written in the other-volatile register, on the

following STOP condition. Up to four bytes can be sent sequentially. If any more data bytes are sent after the second byte, they will not be

acknowledged and no bytes will be written to the non-volatile registers. After a byte is read from or written to the EEPROM, the part

automatically points to the next non-volatile register. If the command code was FFH, the MUX_IN values are sent with the three MSBs padded

with zeroes as shown below. If the command codes was 00H, then the non-volatile register 1 is sent, and if the command code was 01H, then

the non-volatile register 1 is sent.

EEPROM Byte 0 Register

Write

EEPROM 0

Data F

EEPROM 0

Data E

EEPROM 0

Data D

EEPROM 0

Data C

EEPROM 0

Data B

EEPROM 0

Data A

Read

EEPROM 0

Data F

EEPROM 0

Data E

EEPROM 0

Data D

EEPROM 0

Data C

EEPROM 0

Data B

EEPROM 0

Data A

Default

EEPROM Byte 1 Register

Write

EEPROM 1

Data F

EEPROM 1

Data E

EEPROM 1

Data D

EEPROM 1

Data C

EEPROM 1

Data B

EEPROM 1

Data A

Read

EEPROM 1

Data F

EEPROM 1

Data E

EEPROM 1

Data D

EEPROM 1

Data C

EEPROM 1

Data B

EEPROM 1

Data A

Default

EEPROM Byte 2 Register

Write

EEPROM 2

Data F

EEPROM 2

Data E

EEPROM 2

Data D

EEPROM 2

Data C

EEPROM 2

Data B

EEPROM 2

Data A

Read

EEPROM 2

Data F

EEPROM 2

Data E

EEPROM 2

Data D

EEPROM 2

Data C

EEPROM 2

Data B

EEPROM 2

Data A

Default

EEPROM Byte 3 Register

Write

EEPROM 3

Data F

EEPROM 3

Data E

EEPROM 3

Data D

EEPROM 3

Data C

EEPROM 3

Data B

EEPROM 3

Data A

Read

EEPROM 3

Data F

EEPROM 3

Data E

EEPROM 3

Data D

EEPROM 3

Data C

EEPROM 3

Data B

EEPROM 3

Data A

Default

MUX_IN Register

Read

MUX_IN

Data F

MUX_IN

Data E

MUX_IN

Data D

MUX_IN

Data C

MUX_IN

Data B

MUX_IN

Data A

If the command byte is a MUX command byte, any additional data bytes sent after the MUX command code will not be acknowledged. If the

read/write bit in the address is a logic 1, then a read operation follows and the data sent out depends on the previously stored command code.

The MUX_SELECT_1 pin can function as the over-ride pin as on the PCA9559 if the non-volatile register 1 is left at all 0s.

The NON_MUXED_OUT pin is a latched output. It is latched when MUX_SELECT_0 = 1. It is transparent when the MUX_SELECT_0 = 0. The

data sent out on the NON_MUXED_OUT output is the 6th most significant bit of the non-volatile register. Whether this comes from the

non-volatile register 0 or non-volatile register 1 depends on the command code or the external mux-select pins.

After a valid I2C write operation to the EEPROM, the part cannot be addressed via the I2C for 3.6 ms. If the part is addressed prior to this time,

the part will not acknowledge its address.

NOTE:

1. To ensure data integrity, the non-volatile register must be internally write protected when VDD to the I2C-bus is powered down or VDD to the

component is dropped below normal operating levels.

PCA9561 数据表(PDF) 5 Page - NXP Semiconductors

PCA9561 数据表(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

数据表下载

链接网址

PCA9561 数据表(PDF) 5 Page - NXP Semiconductors

PCA9561 数据表(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

数据表 下载

链接网址

数据表下载