Rev. 07.18.11_10

µMP Series

1 of 6

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Electrical Specifications

Input

Input range:

85 - 264 Vac, 120 - 350 Vdc (limited to 250 Vac/300 Vdc in medical apps)

Frequency:

47 - 440 Hz

Inrush current:

40 A peak max. (soft start)

Efficiency:

Up to 91% @ full case load

Power Factor:

0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)

Turn-on time:

AC on 2 sec for uMP1 and 1.5 sec for uMP4, inhibit/enable 250 ms typical

EMI filter:

CISPR 22/EN55022 Level “B”

Leakage current:

300 µA max. @ 240 Vac for uMP1 and 500 µA max for uMP4; 47 - 63 Hz

Radiated EMI:

CISPR 22/EN55022 Level “B”

Holdover storage:

16.7 ms minimum (independent of input Vac, 0 °C to 50 °C))

AC OK:

Signal goes low indicating loss of AC input.

Hold up = Full cycle ride thru (50 Hz)

Harmonic distortion:

Meets EN61000-3-2

Isolation:

Meets EN60950 and EN60601

Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; fan off when unit is inhibited

Input fuse (internal):

uMP1: 16 A/250 V TLAG, uMP4: 10 A / 250 V. (both lines fused)

Warranty:

2 years

µMP Series

Up to 1200 Watts

Special Features

• Full Medical EN60601 approval

• PMBus

• Highefficiency

• Currentlimitmodification

(foldback or constant current)

• Highpowerdensity.

uMP4: 10.8 W/cu-in

uMP1: 15.1 W/cu-in

• Intelligentfan

(speed control/fault status)

• DownloadableGUIfromwebsite

• uPcontrolledPFCinputwithactive

inrush protection

• Optionalconformalcoating

• Industrialtemprange(-40ºC to 70 ºC)

• Nopreloadrequired

• Industrialshock/vibration(>50G’s)

• Lowcost

• IECorterminalblockinput

• Lowprofile1Usize

Total Power: Up to 1200 Watts

Input Voltage: 85 - 264 Vac

120-300 Vdc

# of Outputs: Up to 12

Safety

• UL

UL60950/UL60601-1

• CSA

CSA22.2 No. 234 Level 5

• VDE

EN60950/EN60601-1

• BABT

Compliance to

EN60950/EN60601 BS7002

• CB

Certificate and report

• CE

MarktoLVD

• CCC

Approved

• BSMI

Approved

MicroMP 1U Multi Output

Operating temperature:

-40°to70°Cambient.Derateeachoutput2.5%perdegreefrom50°Cto70°C.

( -20 °C start up). Meets full spec after 1/2 load. 10 min warm-up

Storage temperature:

-40 °C to 85 °C

Electromagnetic susceptibility: DesignedtomeetEN61000-4;-3,-6,-11Level3,Level4for-2,-4,-5

Humidity:

Operating; non-condensing 10% to 95% RH

Vibration:

MIL-STD-810E

MTBF demonstrated:

>350,000hoursatfullload,oneuMP4case+twomodules,TelcordiaSR-332

calculated MTBF

Altitude:

Up to 10k feet; derate linear to 50% from 10k-30k feet

Environmental Specifications

µMP4C shown