HT46R006 datasheet(39/72 Pages) HOLTEK

39 / 72 page

HT48R006/HT46R006

Rev. 1.00

October 24, 2011

rupt Enable bit in the corresponding Interrupt Control

As the external timer pin is shared with an I/O pin, to en-

sure that the pin is configured to operate as an event

counter input pin, two things have to happen. The first is

to ensure that the Operating Mode Select bits in the

Timer Control Register place the Timer/Event Counter in

the Event Counting Mode, the second is to ensure that

the port control register configures the pin as an input. It

should be noted that in the event counting mode, even if

the microcontroller is in the Sleep Mode, the

Timer/Event Counter will continue to record externally

changing logic events on the timer input TCn pin. As a

result when the timer overflows it will generate a timer

interrupt and corresponding wake-up source.

Pulse Width Capture Mode

In this mode, the Timer/Event Counter can be utilised to

measure the width of external pulses applied to the ex-

ternal timer pin. To operate in this mode, the Operating

Mode Select bit pair, TnM1/TnM0, in the Timer Control

Control Register Operating Mode

Select Bits for the Pulse Width

Capture Mode

Bit7 Bit6

In this mode the internal clock, fSYS ,fSYS/4 or the LXT, is

used as the internal clock for the 8-bit Timer/Event

Counter. However, the clock source, fSYS, for the 8-bit

timer is further divided by a prescaler, the value of which

is determined by the Prescaler Rate Select bits

TnPSC2~TnPSC0, which are bits 2~0 in the Timer Con-

trol Register. After the other bits in the Timer Control

bit 4 of the Timer Control Register, can be set high to en-

able the Timer/Event Counter, however it will not actu-

ally start counting until an active edge is received on the

external timer pin.

If the Active Edge Select bit TnEG, which is bit 3 of the

Timer Control Register, is low, once a high to low transi-

tion has been received on the external timer pin, the

Timer/Event Counter will start counting until the external

timer pin returns to its original high level. At this point the

enable bit will be automatically reset to zero and the

Timer/Event Counter will stop counting. If the Active

Edge Select bit is high, the Timer/Event Counter will be-

gin counting once a low to high transition has been re-

ceived on the external timer pin and stop counting when

the external timer pin returns to its original low level. As

before, the enable bit will be automatically reset to zero

and the Timer/Event Counter will stop counting. It is im-

portant to note that in the pulse width capture Mode, the

enable bit is automatically reset to zero when the exter-

nal control signal on the external timer pin returns to its

original level, whereas in the other two modes the en-

able bit can only be reset to zero under program control.

The residual value in the Timer/Event Counter, which

can now be read by the program, therefore represents

the length of the pulse received on the TCn pin. As the

enable bit has now been reset, any further transitions on

the external timer pin will be ignored. The timer cannot

begin further pulse width capture until the enable bit is

set high again by the program. In this way, single shot

pulse measurements can be easily made.

It should be noted that in this mode the Timer/Event

Counter is controlled by logical transitions on the external

timer pin and not by the logic level. When the Timer/Event

Counter is full and overflows, an interrupt signal is gener-

ated and the Timer/Event Counter will reload the value al-

ready loaded into the preload register and continue

counting. The interrupt can be disabled by ensuring that

the Timer/Event Counter Interrupt Enable bit in the corre-

sponding Interrupt Control Register, is reset to zero.

As the TCn pin is shared with an I/O pin, to ensure that

the pin is configured to operate as a pulse width capture

pin, two things have to happen. The first is to ensure that

the Operating Mode Select bits in the Timer Control

width capture Mode, the second is to ensure that the

port control register configures the pin as an input.

+ 1

+ 2

+ 3

+ 4

T i m e r

E x t e r n a l T C n

P i n I n p u t

T n O N - w i t h T n E = 0

P r e s c a l e r O u t p u t

I n c r e m e n t

T i m e r C o u n t e r

P r e s c a l e r O u t p u t i s s a m p l e d a t e v e r y f a l l i n g e d g e o f T 1 .

Pulse Width Capture Mode Timing Chart (TnEG=0)

HT46R006 数据表(PDF) 39 Page - Holtek Semiconductor Inc

HT46R006 数据表(HTML) 39 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

数据表下载