LP2950 datasheet(3/13 Pages) SIPEX

3 / 13 page

Rev. 8/10/01

LP2950/51 100mA Low Dropout Voltage Regulators

LP2950/51

PARAMETER

CONDITIONS

(Note 2)

LP2951AC

Min.

Typ.

Max.

LP2951C

Min.

Typ.

Max.

UNITS

8-Pin Versions only (Continued)

Reference Voltage

Temperature

Coefficient

ppm/¡C

Feedback Pin Bias

Current

Temperature Coefficient

0.1

nA/¡C

Error Comparator

Output Leakage Current

VOH = 30V

0.01

µA

Output Low Voltage

VIN = 4.5V

IOL = 400µA

150

250

150

250

Upper Threshold

Voltage

(Note 7)

Lower Threshold

Voltage

(Note 7)

Hysteresis

(Note 7)

Shutdown Input

Input logic Voltage

Low (Regulator ON)

High (Regulator OFF)

2.0

1.3

0.7

2.0

1.3

0.7

Shut down Pin Input

Current

VS = 2.4V

VS= 30V

675

800

675

800

µA

Regulator Output

Current in Shutdown

(Note 8)

µA

Note 1: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range.

Note 2: Unless otherwise specified all limits guaranteed for TJ = 25°C, VIN = 6V, IL = 100µA and CL = 1µF. Additional conditions for the 8-pin versions are feedback

tied to 5V tap and output tied to output sense (VOUT = 5V) and VSHUTDOWN ≤ 0.8V.

Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are

covered under the specification for thermal regulation.

Note 4: Line regulation for the LP2951 is tested at IL = 1mA. For IL = 100 µA and TJ = 125°C, line regulation is guaranteed by design to 0.2%. See typical

performance characteristics for line regulation versus temperature and load current.

Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V differential. At

very low values of programmed output voltage, the minimum input supply voltage of 2V (2.3V over temperature) must be taken into account.

Note 6: VREF ≤VOUT ≤ (VIN - 1V), 2.3 ≤VIN≤30V, 100µA≤IL≤ 100mA, TJ ≤ TJMAX.

Note 7: Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage measured at 6V input. To

express these thresholds in terms of output voltage change, multiply by the error amplifier gain = VOUT/VREF = (R1 + R2)/R2. For example, at a programmed output

voltage of 5V, the error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain constant as a percent of VOUT as VOUT

is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.

Note 8: VSHUTDOWN ≥ 2V, VIN ≤ 30V, VOUT =0, Feedback pin tied to 5V Tap.

Note 9: All typical values are not guaranteed. The value could vary from lot to lot.

LP2950 数据表(PDF) 3 Page - Sipex Corporation

LP2950 数据表(HTML) 3 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

数据表下载

链接网址

LP2950 数据表(PDF) 3 Page - Sipex Corporation

LP2950 数据表(HTML) 3 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

数据表 下载

链接网址

数据表下载