CD74ACT05-Q1 datasheet(2/6 Pages) TI1

2 / 6 page

CD74ACT05-Q1

HEX INVERTER

WITH OPEN-DRAIN OUTPUTS

SCHS350A − JANUARY 2004 − REVISED JANUARY 2008

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†

Supply voltage range, VCC

−0.5 V to 6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1)

±20 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1)

±50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous output current, IO (VO = 0 to VCC)

±50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous current through VCC or GND

±100 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Package thermal impedance,

θJA (see Note 2)

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg

−65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

2. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions (see Note 3)

TA = 25°C

−40

°C TO

125

°C

UNIT

MIN

MAX

MIN

MAX

UNIT

VCC

Supply voltage

4.5

5.5

4.5

5.5

VIH

High-level input voltage

VIL

Low-level input voltage

0.8

Input voltage

VCC

Output voltage

5.5

IOH

High-level output current

−24

IOL

Low-level output current

∆t/∆v Input transition rise or fall rate

ns/V

NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,

Implications of Slow or Floating CMOS Inputs, literature number SCBA004.

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

VCC

TA = 25°C

−40

°C TO

125

°C

UNIT

PARAMETER

TEST CONDITIONS

VCC

MIN

MAX

MIN

MAX

UNIT

IOL = 50 µA

4.5 V

0.1

VOL

VI = VIH or VIL

IOL = 24 mA

4.5 V

0.36

0.5

VOL

VIH or VIL

IOL = 50 mA‡

5.5 V

1.65

VI = VCC or GND

5.5 V

±0.1

±1

µA

ICC

VI = VCC or GND,

IO = 0

5.5 V

µA

∆ICC

VI = VCC − 2.1 V

4.5 V to 5.5 V

2.4

‡ Test one output at a time, not exceeding 1-second duration. Measurement is made by forcing indicated current and measuring voltage to minimize

power dissipation. Test verifies a minimum 75-

Ω transmission-line drive capability at 125°C.

CD74ACT05-Q1 数据表(PDF) 2 Page - Texas Instruments

CD74ACT05-Q1 数据表(HTML) 2 Page - Texas Instruments

Html Pages

1 2 3 4 5 6

数据表下载

链接网址

CD74ACT05-Q1 数据表(PDF) 2 Page - Texas Instruments

CD74ACT05-Q1 数据表(HTML) 2 Page - Texas Instruments

Html Pages

1 2 3 4 5 6

数据表 下载

链接网址

数据表下载