ATS642LSH_09 datasheet(14/16 Pages) ALLEGRO

14 / 16 page

Two-Wire True Zero Speed Miniature Differential

Peak-Detecting Gear Tooth Sensor with Continuous Calibration

ATS642LSH

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Power Derating

The device must be operated below the maximum junction

temperature of the device, TJ(max). Under certain combinations of

peak conditions, reliable operation may require derating sup-

plied power or improving the heat dissipation properties of the

application. This section presents a procedure for correlating

factors affecting operating TJ. (Thermal data is also available on

the Allegro MicroSystems Web site.)

The Package Thermal Resistance, RJA, is a figure of merit sum-

marizing the ability of the application and the device to dissipate

heat from the junction (die), through all paths to the ambient air.

Its primary component is the Effective Thermal Conductivity,

K, of the printed circuit board, including adjacent devices and

traces. Radiation from the die through the device case, RJC, is

relatively small component of RJA. Ambient air temperature,

TA, and air motion are significant external factors, damped by

overmolding.

The effect of varying power levels (Power Dissipation, PD), can

be estimated. The following formulas represent the fundamental

relationships used to estimate TJ, at PD.

PD = VIN

× IIN

(1)



T = PD

× RJA

(2)

TJ = TA + ΔT

(3)

For example, given common conditions such as: TA= 25°C,

VCC = 12 V, ICC = 4 mA, and RJA = 140 °C/W, then:

PD = VCC

× ICC = 12 V × 4 mA = 48 mW

T = PD

× RJA = 48 mW × 140 °C/W = 7°C

TJ = TA + T = 25°C + 7°C = 32°C

A worst-case estimate, PD(max), represents the maximum allow-

able power level (VCC(max), ICC(max)), without exceeding TJ(max),

at a selected RJA and TA.

Example: Reliability for VCC at TA=150°C, package SH

(I1 trim), using minimum-K PCB

Observe the worst-case ratings for the device, specifically:

RJA=126°C/W, TJ(max) =165°C, VCC(max)=24V, and

ICC(max) = 16mA.

Calculate the maximum allowable power level, PD(max). First,

invert equation 3:

Tmax = TJ(max) – TA = 165°C–150°C = 15°C

This provides the allowable increase to TJ resulting from internal

power dissipation. Then, invert equation 2:

PD(max) = Tmax÷RJA =15°C÷126 °C/W=119mW

Finally, invert equation 1 with respect to voltage:

VCC(est) = PD(max) ÷ ICC(max)= 119mW÷16mA=7 V

The result indicates that, at TA, the application and device can

dissipate adequate amounts of heat at voltages ≤VCC(est).

Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reli-

able operation between VCC(est) and VCC(max) requires enhanced

RJA. If VCC(est) ≥ VCC(max), then operation between VCC(est) and

VCC(max) is reliable under these conditions.

ATS642LSH 数据表(PDF) 14 Page - Allegro MicroSystems

ATS642LSH 数据表(HTML) 14 Page - Allegro MicroSystems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表下载