AD53513JSQ datasheet(3/4 Pages) AD

3 / 4 page

–3–

REV. 0

AD53513

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection.

Although the AD53513 features proprietary ESD protection circuitry, permanent damage may

occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD

precautions are recommended to avoid performance degradation or loss of functionality.

ABSOLUTE MAXIMUM RATINGS

Power Supply Voltage

+VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 V

–VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V

+VS to –VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V

Inputs

DATA,

DATA, INH, INH, RLD, VBB . . . . . . . +5 V, –3 V

DATA to

DATA, INH to INH, RLD, VBB . . . . . . . . .

±3V

VH, VL, VT to GND . . . . . . . . . . . . . . . . . . . . . . +7 V, –2 V

VH to VL (VH – VT) and (VT – VL) . . . . . . . . . . . . . . . .

±9V

Outputs

VOUT Short Circuit Duration . . . . . . . . . . . . . . . Indefinite

VOUT Range in Inhibit Mode

VHDCPL . . . . . Do Not Connect Except for Capacitor to VCC

VLDCPL . . . . . Do Not Connect Except for Capacitor to VEE

THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 V, 0 V

Environmental

Operating Temperature (Junction) . . . . . . . . . . . . . . . 175

°C

Storage Temperature . . . . . . . . . . . . . . . . –65

°C to +150°C

Lead Temperature (Soldering, 10 sec)

. . . . . . . . . . . 260

°C

NOTES

1Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the

device at these or any other conditions above those indicated in the operational

sections of this specification is not implied. Absolute maximum limits apply

individually, not in combination. Exposure to absolute maximum rating condi-

tions for extended periods may affect device reliability.

2Output short circuit protection is guaranteed as long as proper heat sinking is

employed to ensure compliance with the operating temperature limits.

3To ensure lead coplanarity (

± 0.002 inches) and solderability, handling with bare

hands should be avoided and the device should be stored in environments at 24

°C

±5°C (75°F ±10°F) with relative humidity not to exceed 65%.

WARNING!

ESD SENSITIVE DEVICE

ORDERING GUIDE

Shipment Method,

Package

Quantity Per

Package

Model

Description

Shipping Container

Option

AD53513JSQ

100-Lead LQFP-CDQUAD

Tray, 90 Pieces

SQ-100

Parameter

Min

Typ

Max

Unit

Test Conditions

DYNAMIC PERFORMANCE, INHIBIT

Delay Time, Active to Inhibit

1.5

2.5

Measured at 50%, VH = +2 V, VL = –2 V, VT = –2 V

Delay Time, Inhibit to Active

0.7

1.7

Measured at 50%, VH = +2 V, VL = –2 V, VT = –2 V

I/O Spike

<200

mV p-p

VH = 0 V, VL = 0 V, VT = –2 V

Output Capacitance

Driver Inhibited

DYNAMIC PERFORMANCE, VTERM

Delay Time, Active to VTERM

0.50

1.30

Measured at 50%, VH = +0.8 V, VL = –0.8 V, VT = 0 V

Delay Time, VTERM to Active

0.45

1.25

Ω Terminated

Overshoot, Undershoot, and Preshoot

VL = –2 V, VH = +2 V, VT = 0 V

VTERM to VL or VH

±6%/±75

VL = –0.8 V, VH = +0.8 V, VT = 0 V

Output Terminated 50

Ω

POWER SUPPLIES

Total Supply Range

Positive Supply

Negative Supply

–6

Positive Supply Current

570

Negative Supply Current

570

Total Power Dissipation

8.6

Temperature Sensor Gain Factor

1.0

µA/K

RLOAD = 4.2 k

Ω, V

SOURCE = 9 V

NOTES

Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.

*Typical parameters are not production tested but guaranteed through characterization.

Specifications subject to change without notice.

AD53513JSQ 数据表(PDF) 3 Page - Analog Devices

AD53513JSQ 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4

数据表下载