REV. A

AD7724

–6–

PIN FUNCTION DESCRIPTIONS

Mnemonic

Description

AVDD

Analog Positive Supply Voltage, 5 V

± 5%.

AGND

Ground reference point for analog circuitry.

AVIN(–), AVIN(+)

Analog Input to Modulator A. In unipolar operation, the analog input range on AVIN(+) is AVIN(–) to

(AVIN(–) + VREF); for bipolar operation, the analog input range on AVIN(+) is (AVIN(–)

± VREF/2). The

absolute analog input range must lie between 0 and AVDD. The input range is continuously sampled and

processed by the analog modulator.

STBY

Standby, Logic Input. When STBY is high, the device is placed in a low power mode. When STBY is low, the

device is powered up.

MZERO

Digital Control Input. When MZERO is high, the modulator inputs are internally grounded i.e. tied to AGND

in unipolar mode and REF2 in bipolar mode. MZERO allows on-chip offsets to be calibrated out. MZERO is

low for normal operation.

RESET

Reset Logic Input. RESET is an asynchronous input. When RESET is taken high, the sigma-delta modulator

is reset by shorting the integrator capacitors in the modulator. DVAL goes low for 20 MCLK cycles while the

modulator is being reset.

XTAL1

Input to Crystal Oscillator Amplifier. If an external clock is used, XTAL1 should be tied to AGND.

XTAL2/MCLK

Clock Input. An external clock source can be applied directly to this pin with XTAL_OFF tied high. Alterna-

tively, a parallel resonant fundamental frequency crystal, in parallel with a 1 M

Ω resistor, can be connected

between XTAL1 and XTAL2 with XTAL_OFF tied low. External capacitors are then required from the XTAL1

and XTAL2 pins to ground. Consult the crystal manufacturer's recommendation for the load capacitors.

A sine wave can also be used to provide the clock. A sine wave with a voltage swing between 0.4 V p-p and

4 V p-p is needed. XTAL_OFF is tied low and a 1 M

Ω resistor is needed between XTAL1 and XTAL2. A

22 pF capacitor is connected in parallel with this resistor. The sine wave is ac coupled to XTAL1 using a

120 pF capacitor. The use of a sine wave to generate the clock eliminates the need for a square wave clock

source which introduces noise.

DVDD

Digital Supply Voltage, 5 V

± 5%.

DGND

Ground reference for the digital circuitry.

ADATA

Modulator A Bit Stream. The digital bit stream from the sigma-delta modulator is output at ADATA.

BDATA

Modulator B Bit Stream. The digital bit stream from the sigma-delta modulator is output at BDATA.

SCLK

Serial Clock, Logic Output. The bit stream from modulator A and modulator B is valid on the rising edge of

ASCLK.

DVDD1

Digital Supply Voltage for the digital outputs. DVDD1 can have a value of 5 V

± 5% or 3 V ± 5% so that the

logic outputs can be 3 V or 5 V compatible.

DVAL

Data Valid Logic Output. A logic high on DVAL indicates that the data bit stream from the AD7724 is an

accurate digital representation of the analog voltage at the input to the sigma-delta modulator. The DVAL pin

is set low for 20 MCLK cycles if the analog input is overranged.

XTAL_OFF

Oscillator Enable Input. A logic high disables the crystal oscillator amplifier to allow use of an external clock

source. XTAL_OFF is set to a logic low when an external crystal is used between XTAL1 and XTAL2.

BIP

Analog Input Range Select, Logic Input. A logic low on this input selects unipolar mode. A logic high selects

bipolar mode.

GC

Digital Control Input. When GC is high, the gain error of the modulator can be calibrated.

BVIN(–), BVIN(+) Analog Input to Modulator B. In unipolar operation, the analog input range on BVIN(+) is BVIN(–) to

(BVIN(–) + VREF); for bipolar operation, the analog input range on BVIN(+) is (BVIN(–)

± VREF/2). The

absolute analog input range must lie between 0 and AVDD. The input range is continuously sampled and

processed by the analog modulator.

REF2B

Reference Input/Output to Sigma-Delta Modulator B. REF2B connects to the output of an external buffer

amplifier used to drive sigma-delta modulator B. When REF2B is used as an input, REF1 must be connected

to AGND.

REF1

Reference Input/Output. REF1 connects through 3 k

Ω to the output of the internal 2.5 V reference and to the

input of two buffer amplifiers that drive

Σ-∆ modulator A and Σ-∆ modulator B. The pin can be overdriven

with an external 2.5 V reference.

REF2A

Reference Input/Output to Sigma-Delta Modulator A. REF2A connects to the output of an external buffer

amplifier used to drive sigma-delta modulator A. When REF2A is used as an input, REF1 must be connected

to AGND.