CMP04 datasheet(2/8 Pages) AD

2 / 8 page

REV. D

–2–

CMP04–SPECIFICATIONS

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

Input Offset Voltage

VOS

RS = 0

Ω, RL = 5.1 kΩ, VO = 1.4 V1

0.4

Input Offset Current

IOS

IIN(+) – IIN(–), RL = 5.1 k

Ω, V

O = 1.4 V

Input Bias Current

IIN(+) or IIN(–)

100

Voltage Gain

≥ 15 kΩ, V+ = 15 V2

200

V/mV

Large Signal Response Time

VIN = TTL Logic Swing, VREF = 1.4 V

VRL = 5 V, RL = 5.1 k

Ω

300

Small Signal Response Time

VIN = 100 mV Step

3, 5 mV Overdrive

VRL = 5 V, RL = 5.1 k

Ω

1.3

µs

Input Voltage Range

CMVR

Note 4

V+ – 1.5

Common-Mode Rejection Ratio

CMRR

Notes 2, 5

100

Power Supply Rejection Ratio

PSRR

V+ = 5 V to 18 V

100

Saturation Voltage

VOL

VIN(–)

≥ 1 V, V

IN(+) = 0, ISINK

≤ 4 mA

250

400

Output Sink Current

ISINK

VIN(–)

≥ 1 V, VIN(+) = 0, VO ≤ 1.5 V

Output Leakage Current

ILEAK

VIN(+)

≥ 1 V, V

IN(–) = 0, VO = 30 V

0.1

100

Supply Current

I+

RL =

∞, All Comps V+ = 30 V

0.8

2.0

NOTES

1At output switch point, V

O = 1.4 V, RS = 0

Ω with V+ from 5 V, and over the full input common-mode range (0 V to V+ – 1.5 V).

2Guaranteed by design.

3Sample tested.

4The input common-mode voltage or input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range

is V+ – 1.5 V, but either or both inputs can go to 30 V without damage.

≥ 15 kΩ, V+ = 15 V, V

CM = 1.5 V to 13.5 V.

Specifications subject to change without notice.

ELECTRICAL CHARACTERISTICS (@ V+ = 5 V, T

A = 25 C, unless otherwise noted.)

ABSOLUTE MAXIMUM RATINGS

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . +36 V or

±18 V

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . 36 V dc

Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +36 V

Operating Temperature Range

CMP04FS . . . . . . . . . . . . . . . . . . . . . . . . . –40

°C to +85°C

Junction Temperature (TJ) . . . . . . . . . . . . . –65

°C to +150°C

Storage Temperature Range . . . . . . . . . . . . –65

°C to +150°C

Input Current (VIN < –3.0 V) . . . . . . . . . . . . . . . . . . . 50 mA

Output Short Circuit to GND . . . . . . . . . . . . . . . . Continuous

Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . 300

°C

Package Type

Unit

14-Lead SOIC

120

°C/W

NOTES

1Absolute maximum ratings apply to both DICE and packaged parts, unless

otherwise noted. Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress rating only; functional

operation of the device at these or any other conditions above those listed in the

operational sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

JA is specified for worst-case mounting conditions, i.e.,

JA is specified for device

soldered to printed circuit board for SOIC package.

ORDERING GUIDE

TA = 25 C

Temperature

Package

Model

VOS

Ranges

Descriptions

Options

CMP04FS

1 mV

–40

°C to +85°C

14-Lead SOIC

R-14

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection. Although

the CMP04 features proprietary ESD protection circuitry, permanent damage may occur on

devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are

recommended to avoid performance degradation or loss of functionality.

WARNING!

ESD SENSITIVE DEVICE

CMP04 数据表(PDF) 2 Page - Analog Devices

CMP04 数据表(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

数据表下载