56

Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033

800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com

140 Watt Global Performance Switchers

SPECIFICATIONS:

Ac Input

85-264 Vac, 47-63 Hz single phase.

Input Current

Maximum input current at 120 Vac, 60 Hz with full rated

output load: 3.7 A

Hold-Up Time

20ms minimum from loss of ac input at full load, nominal

line (115 Vac).

Output Power

140 W convection; 160 W with air flow. Peak ratings are

for 60 s maximum duration, 10% duty cycle.

Overload Protection

Fully protected against short circuit and output overload.

Short circuit protection is cycling type power limit on

output 1. Recovery after fault is automatic.

Overvoltage Protection

Main outputs: 130% ± 15% typical.

Efficiency

70% at full rated load, nominal input voltage, depending

on model and load distribution.

Input Protection

Internal ac fuse provided. Designed to blow only if a

catastrophic failure occurs in the unit.

Inrush Current

Inrush is limited by internal thermistors. Inrush at 240 Vac,

averaged over the first ac half-cycle under cold start

conditions will not exceed 60 A.

Temperature Coefficient

0.03%/°C typical on all outputs.

Thermal Shutdown

Provided as a standard feature. Designed to protect unit

from prolonged overtemperature.

Environmental

Designed for 0 to 50°C operation at full rated output

power; derate output current and total output power by

2.5% per °C above 50°C. See Environmental and

Packaging Specifications on next page.

Power Fail

TTL- or CMOS-compatible output goes low (< 0.5 V) 5 ms

before output voltage drops more than 4% below

nominal voltage upon loss of ac power. The signal is

factory set to trip on 84 to 94 Vac brown-out depending

upon incoming line impedance and distortion. Other

settings are available to the user through adjustment of

built-in potentiometer.

FEATURES:

• Wide-range ac input 85-264 Vac

• 2-year warranty

• Conducted EMI exceeds FCC Class B and CISPR 22

Class B (Commercial models) and CISPR 11 Class B

(Medical models)

• Single outputs

• Commercial Approved to UL1950, IEC950,

EN60950 and CSA22.2-234 L3

• Medical Approved to UL2601-1, IEC601-1 and

CSA22.2 No. 601

•

marked to LVD

Output Noise

0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential

mode. Measured with noise probe directly across output

terminals of the power supply.

Transient Response

Main output—500 µs typical response time for return to

within 0.5% of final value for a 50% load step change.

∆i/

∆t<0.2 A/µs. Maximum voltage deviation is 3.5%. Startup/

shutdown overshoot less than 3%.

Remote Sense

Provided as a standard feature.

Voltage Adjustment

Built-in potentiometer adjusts voltage ±5%.

Overload Protection

Factory set to begin power limiting at approximately 175 W.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the

following emissions requirements:

EMI SPECIFICATIONS

COMPLIANCE LEVEL

Conducted Emissions GPC140 EN55022 Class B; FCC Class B

Conducted Emissions GPM140 EN55011 Class B; FCC Class B

Static Discharge

EN61000-4-2, 6 kV contact, 8 kV air

RF Field Susceptibility

EN61000-4-3, 3 V/meter

Fast Transients/Bursts

EN61000-4-4, 2 kV, 5 kHz

Surge Susceptibility

EN61000-4-5, 1 kV diff., 2 kV com.

Commercial Leakage Current

0.95 mA 254 Vac @ 60 Hz input.

Commercial Safety

Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950

and EN60950. UL file #E135803 commercial; CSA

#LR46516 all models. The output(s) are intended for

safety earthed Signal Output and Intermediate Circuits

only. All dc outputs are SELV under normal and single

fault conditions.

Medical Leakage Current

60 µA 254 Vac @ 60 Hz input.

Medical Safety

Approved to UL2601, CSA22.2 No. 601 Level 3 and

IEC601. UL file E116994; CSA #LR46516. The output(s)

are intended for safety earthed Signal Output and

Intermediate Circuits only. The output(s) are not accept-

able for patient connection without additional isolation. All

dc outputs are SELV under normal and single fault

conditions.