64

Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033

800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com

200 Watt Global Performance Switchers

SPECIFICATIONS:

Ac Input

85-264 Vac, 47-63 Hz single phase.

Input Current

Maximum input current at 120 Vac, 60 Hz with full rated output

load: 5.5 A

Hold-Up Time

20 ms minimum from loss of ac input at full load, nominal line

(115 Vac).

Output Power

150 W convection; 200 with 26 cfm air; 220 W peak. Peak ratings

are for 60 s maximum duration, 10% duty cycle. During peak

load condition, output regulation may exceed total regulation

limits.

Overload Protection

Fully protected against short circuit and output overload. Short

circuit protection is cycling type power limit on outputs 1 & 2;

foldback type on outputs 3 & 4. Recovery after fault is automatic.

See output ratings chart for additional notes or conditions.

Overvoltage Protection

Main outputs: 124% ± 12% typical.

Efficiency

Minimum 65% at full rated load, nominal input voltage, depending

on model and load distribution.

Input Protection

Internal ac fuse provided. Designed to blow only if a catastrophic

failure occurs in the unit.

Inrush Current

Inrush is limited by internal thermistors. Inrush at 240 Vac under

cold start conditions will not exceed 60 A.

Temperature Coefficient

0.03%/

Thermal Shutdown

Provided as a standard feature. Designed to protect unit from

prolonged overtemperature.

Environmental

Designed for 0 to 50°C operation at full rated output power;

derate output current and total output power by 2.5% per °C

above 50°C. See Environmental and Packaging Specifications

on next page.

FEATURES:

• Wide-range ac input 85-264 Vac

• 2-year warranty

• Conducted EMI exceeds FCC Class B and CISPR 22

Class B (Commercial models) and CISPR 11 Class B

(Medical models)

• Commercial Approved to UL1950, IEC950 and

CSA22.2-234 L3

• Medical Approved to UL2601-1, IEC601-1 and

CSA22.2 No. 601

• Multiple outputs

•

marked to LVD

Power Fail

TTL- or CMOS-compatible output goes low (< 0.5 V) 5 ms

before output voltage drops more than 4% below nominal

voltage upon loss of ac power.The signal is factory set to trip on

84 to 94 Vac brown-out depending upon incoming line impedance

and distortion. Other settings are available to the user through

adjustment of built-in potentiometer.

Output Noise

0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential mode.

Measured with noise probe directly across output terminals of

the power supply.

Transient Response

Main output—500 µs typical response time for return to within

0.5% of final value for a 50% load step change.

∆i/∆t<0.2 A/µs.

Maximum voltage deviation is 3.5%. Startup/shutdown overshoot

less than 3%.

Remote Sense

Provided as a standard feature on main 5 V output.

Voltage Adjustment

Built-in potentiometer adjusts voltage ±5% on output 1 & 2.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the following

emissions requirements:

EMI SPECIFICATIONS

COMPLIANCE LEVEL

Conducted Emissions GPC200 EN55022 Class B; FCC Class B

Conducted Emissions GPM200 EN55011 Class B; FCC Class B

Static Discharge

EN61000-4-2, 6 kV contact, 8 kV air

RF Field Susceptibility

EN61000-4-3, 3 V/meter

Fast Transients/Bursts

EN61000-4-4, 2 kV, 5 kHz

Surge Susceptibility

EN61000-4-5, 1 kV diff., 2 kV com.

Commercial Leakage Current

0.95 mA 254 Vac @ 60 Hz input (with no deviations).

Commercial Safety

Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950 and

EN60950. UL file #E135803 commercial; CSA #LR46516 all

models.The output(s) are intended for safety earthed Signal

Output and Intermediate Circuits only. All dc outputs are SELV

under normal and single fault conditions.

Medical Leakage Current

60 µA 254 Vac @ 60 Hz input.

Medical Safety

Approved to UL2601-1, CSA-C22.2 No. 601 Level 3 and IEC601.

UL file E116994; CSA #LR46516.The output(s) are intended for

safety earthed Signal Output and Intermediate Circuits only.The

output(s) are not acceptable for patient connection without

additional isolation. All dc outputs are SELV under normal and

single fault conditions.