VIPER Remote Control Systems

VIPER Remote Control Systems

VIPER Remote Control Systems

VIPER Remote Control Systems

DS VIPER-2

©2009 REG No 277 4001, Lewes, England. Page 5

VIPER

VIPER

VIPER

VIPER----S1M / VIPER S2M (230Vac Powered Receivers)

S1M / VIPER S2M (230Vac Powered Receivers)

S1M / VIPER S2M (230Vac Powered Receivers)

S1M / VIPER S2M (230Vac Powered Receivers)

Please Note:

Please Note:

Please Note:

Please Note: During Learn and Erase the relays operate at high speed. They should be isolated from sensi-

tive equipment during this process.

To Pair a Transmitter button to receiver Output Relay #1

To Pair a Transmitter button to receiver Output Relay #1

To Pair a Transmitter button to receiver Output Relay #1

To Pair a Transmitter button to receiver Output Relay #1

1.

Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode.

2.

Switch the receiver unit OFF and then ON again in ~1sec intervals FOUR

FOUR

FOUR

FOUR times finally leaving the unit

powered.

3.

After 5 seconds the receiver emits a single ‘buzz’ The unit is now in ‘learn’ Mode

5.

Press the chosen transmitter button.

6.

The receiver will acknowledge by sounding the a single ’buzz’

7.

Press the same transmitter button again, to confirm OK. The receiver will “buz” again to confirm.

8.

Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode.

To Pair a Transmitter button to receiver Output Relay #2

To Pair a Transmitter button to receiver Output Relay #2

To Pair a Transmitter button to receiver Output Relay #2

To Pair a Transmitter button to receiver Output Relay #2

1.

Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode.

2.

Switch the receiver unit OFF and then ON again in ~1sec intervals SIX

SIX

SIX

SIX times finally leaving the unit

powered.

3.

After 5 seconds the receiver emits a double ‘buzz’ The unit is now in ‘learn’ Mode

5.

Press the chosen transmitter button.

6.

The receiver will acknowledge by sounding the a double ’buzz’

7.

Press the same transmitter button again, to confirm OK. The receiver will double “buzz” again to

confirm.

8.

Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode.

Erasing Receivers Memory

Erasing Receivers Memory

Erasing Receivers Memory

Erasing Receivers Memory

1.

Power the receiver unit up and wait 10 seconds for the unit to enter ‘normal operation’ mode.

2.

Switch the unit off and then on again at ~1 second intervals TEN

TEN

TEN

TEN times, leaving the unit powered.

3.

Wait 5 seconds until a ‘clicking’ sound is heard for a period of 10 seconds.

4.

Wait 10 seconds for the receiver unit to return to ‘normal’ mode

5.

The unit has now erased all encoder data.

NOTE:

NOTE:

NOTE:

NOTE: You cannot erase individual Tx encoders

Configuring Receiver Outputs

Configuring Receiver Outputs

Configuring Receiver Outputs

Configuring Receiver Outputs

The jumper links configure the outputs to be Momentary or Latching.

The jumper links are made/removed by the small link ‘cap’ placed

over the pin header.

LK1

LK1

LK1

LK1

Relay #1

Relay #1

Relay #1

Relay #1

LK2

LK2

LK2

LK2

Relay #2

Relay #2

Relay #2

Relay #2

Open

Mom

Open

Mom

Closed

Latch

Closed

Latch

Link Positions

Link Positions

Link Positions

Link Positions ---- Relay Outputs

Relay Outputs

Relay Outputs

Relay Outputs

(the above image shows, RLY2 Momentary, RLY1 Latched)

(the above image shows, RLY2 Momentary, RLY1 Latched)