25LC080C datasheet(13/34 Pages) MICROCHIP

13 / 34 page

 2009-2012 Microchip Technology Inc.

DS22151B-page 13

25XX080C/D

3.0

PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 3-1.

TABLE 3-1:

PIN FUNCTION TABLE

3.1

Chip Select (CS)

A low level on this pin selects the device. A high level

deselects the device and forces it into Standby mode.

However, a programming cycle which is already

initiated or in progress will be completed, regardless of

the CS input signal. If CS is brought high during a

program cycle, the device will go into Standby mode as

soon as the programming cycle is complete. When the

device is deselected, SO goes to the high-impedance

state, allowing multiple parts to share the same SPI

bus. A low-to-high transition on CS after a valid write

sequence initiates an internal write cycle. After power-

up, a low level on CS is required prior to any sequence

being initiated.

3.2

Serial Output (SO)

The SO pin is used to transfer data out of the

25XX080C/D. During a read cycle, data is shifted out

on this pin after the falling edge of the serial clock.

3.3

Write-Protect (WP)

This pin is used in conjunction with the WPEN bit in the

STATUS register to prohibit writes to the nonvolatile

bits in the STATUS register. When WP is low and

WPEN is high, writing to the nonvolatile bits in the

STATUS register is disabled. All other operations

function normally. When WP is high, all functions,

including writes to the nonvolatile bits in the STATUS

low during a STATUS register write sequence will

disable writing to the STATUS register. If an internal

write cycle has already begun, WP going low will have

no effect on the write.

The WP pin function is blocked when the WPEN bit in

the STATUS register is low. This allows the user to

install the 25XX080C/D in a system with WP pin

grounded and still be able to write to the STATUS

WPEN bit is set high.

3.4

Serial Input (SI)

The SI pin is used to transfer data into the device. It

receives instructions, addresses and data. Data is

latched on the rising edge of the serial clock.

3.5

Serial Clock (SCK)

The SCK is used to synchronize the communication

between a master and the 25XX080C/D. Instructions,

addresses or data present on the SI pin are latched on

the rising edge of the clock input, while data on the SO

pin is updated after the falling edge of the clock input.

3.6

Hold (HOLD)

The HOLD pin is used to suspend transmission to the

25XX080C/D while in the middle of a serial sequence

without having to retransmit the entire sequence again.

It must be held high any time this function is not being

used. Once the device is selected and a serial

sequence is underway, the HOLD pin may be pulled

low to pause further serial communication without

resetting the serial sequence. The HOLD pin must be

brought low while SCK is low, otherwise the HOLD

function will not be invoked until the next SCK high-to-

low transition. The 25XX080C/D must remain selected

during this sequence. The SI, SCK and SO pins are in

a high-impedance state during the time the device is

paused and transitions on these pins will be ignored. To

resume serial communication, HOLD must be brought

high while the SCK pin is low, otherwise serial commu-

nication will not resume. Lowering the HOLD line at any

time will tri-state the SO line.

Name

Pin Number

Function

Chip Select Input

Serial Data Output

Write-Protect Pin

VSS

Ground

Serial Data Input

SCK

Serial Clock Input

HOLD

Hold Input

VCC

Supply Voltage

25LC080C 数据表(PDF) 13 Page - Microchip Technology

25LC080C 数据表(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表下载