ADP160ACBZ-2.8-R7 datasheet(4/24 Pages) AD

4 / 24 page

ADP160/ADP161/ADP162/ADP163

Data Sheet

Rev. G | Page 4 of 24

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

UNDERVOLTAGE LOCKOUT

UVLO

Input Voltage Rising

UVLO

RISE

2.19

Input Voltage Falling

UVLO

FALL

1.60

Hysteresis

UVLO

HYS

100

OUTPUT NOISE

OUT

NOISE

10 Hz to 100 kHz, V

IN = 5 V, VOUT = 3.3 V

105

µV

rms

10 Hz to 100 kHz, V

IN = 5 V, VOUT = 2.5 V

100

µV

rms

10 Hz to 100 kHz, V

IN = 5 V, VOUT = 1.2 V

µV

rms

POWER SUPPLY REJECTION RATIO

PSRR

100 Hz, V

IN = 5 V, VOUT = 3.3 V

100 Hz, V

IN = 5 V, VOUT = 2.5 V

100 Hz, V

IN = 5 V, VOUT = 1.2 V

1 kHz, V

IN = 5 V, VOUT = 3.3 V

1 kHz, V

IN = 5 V, VOUT = 2.5 V

1 kHz, V

IN = 5 V, VOUT = 1.2 V

1 Accuracy when VOUT is connected directly to ADJ. When the VOUT voltage is set by external feedback resistors, the absolute accuracy in adjust mode depends on the

tolerances of resistors used.

2 Based on an end-point calculation using 0 μA and 150 mA loads.

3 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output

voltages above 2.2 V.

4 Start-up time is defined as the time between the rising edge of EN to V

OUT being at 90% of its nominal value.

5 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V or 2.7 V.

INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS

Table 2.

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

MINIMUM INPUT AND OUTPUT CAPACITANCE1

MIN

A = −40°C to +125°C

0.7

µF

CAPACITOR ESR

ESR

A = −40°C to +125°C

0.001

0.2

1 The minimum input and output capacitance should be greater than 0.7 µF over the full range of operating conditions. The full range of operating conditions in the

application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;

however, Y5V and Z5U capacitors are not recommended for use with any LDO.

ADP160ACBZ-2.8-R7 数据表(PDF) 4 Page - Analog Devices

ADP160ACBZ-2.8-R7 数据表(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载

链接网址

ADP160ACBZ-2.8-R7 数据表(PDF) 4 Page - Analog Devices

ADP160ACBZ-2.8-R7 数据表(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表 下载

链接网址

数据表下载