COP8SAC7SLB8 datasheet(27/62 Pages) TI

27 / 62 page

8.0 Power Save Modes (Continued)

8.3 MULTI-INPUT WAKEUP

The Multi-Input Wakeup feature is used to return (wakeup)

the device from either the HALT or IDLE modes. Alternately

Multi-Input Wakeup/Interrupt feature may also be used to

generate up to 8 edge selectable external interrupts.

Figure 20 shows the Multi-Input Wakeup logic.

The Multi-Input Wakeup feature utilizes the L Port. The user

selects which particular L port bit (or combination of L Port

bits) will cause the device to exit the HALT or IDLE modes.

The selection is done through the register WKEN. The reg-

ister WKEN is an 8-bit read/write register, which contains a

control bit for every L port bit. Setting a particular WKEN bit

enables a Wakeup from the associated L port pin.

The user can select whether the trigger condition on the

selected L Port pin is going to be either a positive edge (low

to high transition) or a negative edge (high to low transition).

This selection is made via the register WKEDG, which is an

8-bit control register with a bit assigned to each L Port pin.

Setting the control bit will select the trigger condition to be a

negative edge on that particular L Port pin. Resetting the bit

selects the trigger condition to be a positive edge. Changing

an edge select entails several steps in order to avoid a

Wakeup condition as a result of the edge change. First, the

associated WKEN bit should be reset, followed by the edge

select change in WKEDG. Next, the associated WKPND bit

should be cleared, followed by the associated WKEN bit

being re-enabled.

An example may serve to clarify this procedure. Suppose we

wish to change the edge select from positive (low going high)

to negative (high going low) for L Port bit 5, where bit 5 has

previously been enabled for an input interrupt. The program

would be as follows:

RBIT

5, WKEN

; Disable MIWU

SBIT

5, WKEDG

; Change edge polarity

RBIT

5, WKPND

; Reset pending flag

SBIT

5, WKEN

; Enable MIWU

If the L port bits have been used as outputs and then

changed to inputs with Multi-Input Wakeup/Interrupt, a safety

procedure should also be followed to avoid wakeup condi-

tions. After the selected L port bits have been changed from

output to input but before the associated WKEN bits are

enabled, the associated edge select bits in WKEDG should

be set or reset for the desired edge selects, followed by the

associated WKPND bits being cleared.

This same procedure should be used following reset, since

the L port inputs are left floating as a result of reset.

The occurrence of the selected trigger condition for

Multi-Input Wakeup is latched into a pending register called

WKPND. The respective bits of the WKPND register will be

set on the occurrence of the selected trigger edge on the

corresponding Port L pin. The user has the responsibility of

clearing these pending flags. Since WKPND is a pending

the device will not enter the HALT mode if any Wakeup bit is

both enabled and pending. Consequently, the user must

clear the pending flags before attempting to enter the HALT

mode.

WKEN and WKEDG are all read/write registers, and are

cleared at reset. WKPND register contains random value

after reset.

DS012838-27

FIGURE 20. Multi-Input Wake Up Logic

COP8SAC7SLB8 数据表(PDF) 27 Page - Texas Instruments

COP8SAC7SLB8 数据表(HTML) 27 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表下载