ST7LITE29F2 datasheet(120/166 Pages) STMICROELECTRONICS

120 / 166 page

Electrical characteristics

ST7LITE20F2 ST7LITE25F2 ST7LITE29F2

120/166

Doc ID 8349 Rev 5

13.3

Operating conditions

13.3.1

General operating conditions

TA = -40 to +85 °C unless otherwise specified.

Table 58.

Current characteristics

Symbol

Ratings

Maximum value

Unit

IVDD

Total current into VDD power lines (source)

(1)

100

IVSS

Total current out of VSS ground lines (sink)

(1)

100

IIO

Output current sunk by any standard I/O and control pin

Output current sunk by any high sink I/O pin

Output current source by any I/Os and control pin

- 25

IINJ(PIN)

(2) & (3)

Injected current on RESET pin

± 5

Injected current on OSC1 and OSC2 pins

± 5

Injected current on PB0 and PB1 pins (4)

Injected current on any other pin(5)

± 5

ΣIINJ(PIN) (1)

Total injected current (sum of all I/O and control pins)(5)

± 20

All power (VDD) and ground (VSS) lines must always be connected to the external supply.

IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum cannot be

respected, the injection current must be limited externally to the IINJ(PIN) value. A positive injection is induced by VIN>VDD

while a negative injection is induced by VIN<VSS. For true open-drain pads, there is no positive injection current, and the

corresponding VIN maximum must always be respected.

Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout the

device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:

- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage is

lower than the specified limits)

- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as far

as possible from the analog input pins.

No negative current injection allowed on PB0 and PB1 pins.

When several inputs are submitted to a current injection, the maximum

ΣIINJ(PIN) is the absolute sum of the positive and

negative injected currents (instantaneous values). These results are based on characterization with

ΣIINJ(PIN) maximum

current injection on four I/O port pins of the device.

Table 59.

Thermal characteristics

Symbol

Ratings

Value

Unit

TSTG

Storage temperature range

-65 to +150

°C

Maximum junction temperature(1)

−−

(seeTable 90: Thermal characteristics)

ST7LITE29F2 数据表(PDF) 120 Page - STMicroelectronics

ST7LITE29F2 数据表(HTML) 120 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载