| 数据搜索系统,热门电子元器件搜索 |
|
AD8603 数据表(PDF) 12 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD8603 数据表(HTML) 12 Page - Analog Devices |
|
12 / 16 page ![]() AD8603/AD8607/AD8609 Rev. C | Page 12 of 16 APPLICATIONS NO PHASE REVERSAL The AD8603/AD8607/AD8609 do not exhibit phase inversion even when the input voltage exceeds the maximum input common-mode voltage. Phase reversal can cause permanent damage to the amplifier, resulting in system lockups. The AD8603/AD8607/AD8609 can handle voltages of up to 1 V over the supply. TIME (4µs/DIV) VS = ±2.5V VIN = 6V p-p AV = 1 RL = 10kΩ VIN VOUT Figure 41. No Phase Response INPUT OVERVOLTAGE PROTECTION If a voltage 1 V higher than the supplies is applied at either input, the use of a limiting series resistor is recommended. If both inputs are used, each one should be protected with a series resistor. To ensure good protection, the current should be limited to a maximum of 5 mA. The value of the limiting resistor can be determined from the following equation: (VIN − VS)/(RS + 200 Ω) ≤ 5 mA DRIVING CAPACITIVE LOADS The AD8603/AD8607/AD8609 are capable of driving large capacitive loads without oscillating. Figure 42 shows the output of the AD8603/AD8607/AD8609 in response to a 100 mV input signal, with a 2 nF capacitive load. Although it is configured in positive unity gain (the worst case), the AD8603 shows less than 20% overshoot. Simple additional circuitry can eliminate ringing and overshoot. One technique is the snubber network, which consists of a series RC and a resistive load (see Figure 43). With the snubber in place, the AD8603/AD8607/AD8609 are capable of driving capacitive loads of 2 nF with no ringing and less than 3% overshoot. The use of the snubber circuit is usually recommended for unity gain configurations. Higher gain configurations help improve the stability of the circuit. Figure 44 shows the same output response with the snubber in place. VS = ±0.9V VIN = 100mV CL = 2nF RL = 10kΩ Figure 42. Output Response to a 2 nF Capacitive Load, Without Snubber CS 47pF VCC VEE RS 150Ω 200mV CL V+ V– – + Figure 43. Snubber Network VSY = ±0.9V VIN = 100mV CL = 2nF RL = 10kΩ RS = 150Ω CS = 470pF Figure 44. Output Response to a 2 nF Capacitive Load with Snubber Optimum values for RS and CS are determined empirically; Table 5 lists a few starting values. Table 5. Optimum Values for the Snubber Network CL (pF) RS (Ω) CS (pF) 100 to ~500 500 680 1500 100 330 1600 to ~2000 400 100 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |