TC72 datasheet(43/44 Pages) MICROCHIP

43 / 44 page

Analog & Interface Product Selector Guide

LIN Serial Analyzer (APGDT001)

The LIN Serial Analyzer development

system enables a Personal Computer

(PC) to communicate with a LIN (Local

Interface Network) bus . The PC program

uses a graphical user interface to enter

and display message frames occurring on the target bus .

USB to UART Converter Evaluation Board

(MCP2200EV-VCP)

The MCP2200EV-VCP is a USB-to-RS232

development and evaluation board for

the MCP2200 USB-to-UART device . The

board allows for easy demonstration and

evaluation of the MCP2200 . The accompanying software

allows the special device features to be configured and

controlled . The board is powered from USB and has a test

point associated with each GPIO pin . In addition, two of

these pins are connected to LEDs which can be used to

indicate USB-to-UART traffic when the associated pins are

configured as TxLED and RxLED pins respectively.

Linear Products

MCP6V01 Thermocouple Auto-Zeroed

Ref Design Board (MCP6V01RD-TCPL)

The MCP6V01 design board

demonstrates how to use a difference

amplifier system to measure

Electromotive Force (EMF) voltage at

the cold junction of thermocouple in order to accurately

measure temperature of the thermocouple bead . This

can be done by using the MCP6V01 auto-zeroed op amp

because of its ultra low offset Voltage (VOS) and high

Common Mode Rejection Ratio (CMRR) .

MCP6N11 and MCP6V2X Wheatstone Bridge

Reference Design (ARD00354)

This board demonstrates the performance

of Microchip’s MCP6N11 instrumentation

amplifier (INA) and a traditional three op

amp INA using Microchip’s MCP6V26

and MCP6V27 auto-zeroed op amps . The

input signal comes from an RTD temperature sensor in

a Wheatstone bridge . Real world interference is added

to the bridge’s output, to provide realistic performance

comparisons . Data is gathered and displayed on a PC, for

ease of use .

MCP6H04 Evaluation Board (ADM00375)

The MCP6H04 Evaluation Board is intended

to support an instrumentation amplifier

and show the capability of the MCP6H04

operational amplifier. It uses a quad op amp

in a difference amplifier configuration with

input buffers and voltage reference . The test points for the

power supply, ground, input signals, output signals, and

voltage reference allow lab equipment to be connected to

the board .

MCP73X23 OVP Lithium Iron Phosphate Battery

Charger Evaluation Board (MCP73X23EV-LFP)

The MCP73X23 Lithium Iron

Phosphate Battery Charger Evaluation

board demonstrates the features of

Microchip’s MCP73123 and MCP73223

Lithium Iron Phosphate (LiFePO4) Battery Charge

Management Controller with Input Overvoltage Protection .

MCP7383X Li-Ion System Power Path Management

Reference Design (MCP7383XRD-PPM)

This reference design is developed to

assist product designers in reducing

product design cycle and time by

utilizing Microchip’s stand-alone Li-Ion

battery charge management controllers

with system power path management . Due to the natural

characteristics of Li-Ion/Li-Polymer batteries, they are the

most popular power sources for mobile devices, however,

extra care in design is always important . System Power

Path Management allows end-users to charge their

batteries without interruption .

MCP1640 Sync Boost Converter Evaluation Board

(MCP1640EV-SBC)

The MCP1640 Synchronous Boost

Converter Evaluation board demonstrates

the MCP1640 in two boost-converter

applications with multiple output voltages .

It can be used to evaluate both package

options (SOT-23-6 and 2 × 3-8 DFN) . This

board was developed to help engineers

reduce the product design cycle time .

MCP1252 Charge Pump Backlight Demo Board

(MCP1252DM-BKLT)

The MCP1252 board demonstrates

the use of a charge pump device in

an LED application and acts as a

platform to evaluate the MCP1252

device in general . Light intensity is

controlled uniformly through the use of ballast resistors .

A PIC10F206 MCU provides an enable signal to the

MCP1252 and accepts a push-button input that allows the

white LEDs to be adjusted to five different light intensities .

Interface Products

MCP2515 CAN Bus Monitor Demo Board

(MCP2515DM-BM)

The MCP2515 CAN Bus Monitor Demo

board kit contains two identical boards

which can be connected together to

create a simple two node Controller

Area Network (CAN) bus, which can be

controlled and/or monitored via the included PC interface .

The board(s) can also be connected to an existing CAN bus .

Featured Analog Development Tools

TC72 数据表(PDF) 43 Page - Microchip Technology

TC72 数据表(HTML) 43 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载