PC06E8-2S. datasheet(79/80 Pages) AMPHENOL

79 / 80 page

CUT-OUT FOR

PT ONLY

PIN LOCATION FOR PC ONLY

SECTION

JAM NUT MOUNTINGS

FLANGE MOUNTED CONNECTORS

All flange mounting PC and PT connectors use standard MS

mounting dimensions. They cannot be back panel mounted

due to coupling clearance. The PTB (thru-bulkhead) type con-

nector must also be back panel mounted on one side. Flange

gaskets are available for both series, see page 64.

Shell

Size

(TP)

Dia.

PC & PT

.469

.641

.323

.439

.594

.734

.449

.563

.719

.812

.573

.680

.812

.938

.699

.859

.906

1.031

.823

.984

.969

1.125

.949

1.108

1.062

1.203

1.073

1.233

1.156

1.297

1.199

1.358

1.250

1.375

1.323

1.483

1.375

–

1.449

–

JAM NUT MOUNTINGS

The jam nut design has become very popular because it allows

bench wiring of harness assemblies. The labor saving often off-

sets the added cost of the jam nut receptacle which is due to

the self contained “O” ring and the extra nut. The PC series

mounts in a round hole and can be pinned to prevent rotation.

The PT series mounts in a “D” mounting hole and does not

require pinning.

Shell

Size

+.010

–.000

+.000

–.010

±.010

Panel Thickness

Min.

Max.

.447

.420

.286

.062

.125

.572

.542

.331

.062

.125

.697

.669

.375

.062

.125

.884

.830

.442

.062

.125

1.007

.955

.486

.062

.125

1.134

1.084

.530

.062

.125

1.259

1.208

.573

.062

.125

1.384

1.333

.641

.062

.250

1.507

1.459

.685

.062

.250

1.634

1.575

–

.062

.250

HERMETIC RECEPTACLE MOUNTINGS

This series must be mounted in such a way as to preserve the

hermetic seal provided by the glass insert. Mounting data for

box and jam nut receptacles is given above. Cut-out required

for solder mounting receptacles (N) is given below.

Shell

Size

Max.

6.458

8.582

.692

.801

.926

1.051

1.176

1.395

1.375

The finish of each of these hermetic

receptacles is fused electro-deposited

tin for easy solderability, and protected

by a special lacquer for optimum shelf

life. The lacquer will not interfere with

any soldering operation.

Low temperature solder should be used

and the addition of a solder fillet at

arrow points on drawing at right is rec-

ommended. Care must be taken that

the operating temperature of the final

assembly does not rise above the melt-

Mounting Recommendations

for miniature cylindrical connectors

CUT-OUT

SOLDER

RECEPTACLE

JAM NUT

RECEPTACLE

(See dimensions

above)

BOX

RECEPTACLE

(See dimensions

above)

HERMETIC RECEPTACLES

(TP)

D Dia.

.120 Dia. for Shell Sizes 6-22

PC & PT

.147 Dia. for

Size 24 PT

.150 Dia. for

SP only

4 HOLES

CUT-OUT

SECTION

No. 4 Screw

for PC & PT

No. 6 Screw

for SP and for

Size 24 PT

FLANGE MOUNTED CONNECTORS

PC06E8-2S. 数据表(PDF) 79 Page - Amphenol Corporation

PC06E8-2S. 数据表(HTML) 79 Page - Amphenol Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载

链接网址

PC06E8-2S. 数据表(PDF) 79 Page - Amphenol Corporation

PC06E8-2S. 数据表(HTML) 79 Page - Amphenol Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表 下载

链接网址

数据表下载