DM385 datasheet(33/280 Pages) TI1

33 / 280 page

DM385, DM388

www.ti.com

SPRS821D – MARCH 2013 – REVISED DECEMBER 2013

3.2

Pin Assignments

The following table provides a summary of the device signal ball assignments and characteristics.

1. BALL NUMBER: Package ball number(s) associated with each signal(s).

2. BALL NAME: The name of the package ball or terminal.

Note: The table does not take into account subsystem terminal multiplexing options.

3. SIGNAL NAME: The signal name for that ball in the mode being used.

4. PINCNTL REGISTER NAME AND ADDRESS: The name and address of the register that controls the

pin’s internal pull-up/down resistors and multiplexing options.

5. PINCNTL DEFAULT VALUE: The default value of the PINCNTL after reset.

6. MODE: The setting of the MUXMODE[10:0] bits in the associated PINCNTL register that selects this

multiplexed signal option.

7. TYPE: Signal direction

–

I = Input

–

O = Output

–

I/O = Input/Output

–

D = Open drain

–

DS = Differential

–

A = Analog

–

PWR = Power

–

GND = Ground

8. DSIS: The deselected input state (DSIS) indicates the state driven on the peripheral input (logic "0",

logic "1", or "PIN" level) when the peripheral pin function is not selected by any of the PINCNTLx

registers.

–

0: Logic 0 driven on the peripheral's input signal port.

–

1: Logic 1 driven on the peripheral's input signal port.

–

PIN: The value on the pin is driven to the peripheral's input signal port.

9. BALL RESET STATE: The state of the ball during device reset.

–

0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor

–

1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor

–

Z: High-impedance.

–

L: High-impedance with an active pulldown resistor

–

H : High-impedance with an active pullup resistor

10. BALL RESET REL. STATE: The state of the ball following the device coming out of reset.

–

0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor

–

1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor

–

Z: High-impedance.

–

L: High-impedance with an active pulldown resistor

–

H : High-impedance with an active pullup resistor

11. POWER: The voltage supply that powers the terminal’s I/O buffers.

12. HYS: Indicates if the input buffer is with hysteresis.

13. BUFFER TYPE: Drive strength of the associated output buffer.

Device Pins

Submit Documentation Feedback

Product Folder Links: DM385 DM388

DM385 数据表(PDF) 33 Page - Texas Instruments

DM385 数据表(HTML) 33 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载