REV. B

ADDAC80/ADDAC85/ADDAC87

–13–

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

24-Lead Plastic DIP (N-24A)

24

112

13

PIN 1

0.580 (14.73)

0.485 (12.32)

1.290 (32.70)

1.150 (29.30)

0.195 (4.95)

0.125 (3.18)

0.015 (0.381)

0.008 (0.204)

0.625 (15.87)

0.600 (15.24)

SEATING

PLANE

0.060 (1.52)

0.015 (0.38)

0.250

(6.35)

MAX

0.022 (0.558)

0.014 (0.356)

0.200 (5.05)

0.125 (3.18)

0.150

(3.81)

MIN

0.100

(2.54)

BSC

0.070 (1.77)

0.030 (0.77)

CONTROLLING DIMENSIONS ARE IN MILLIMETERS: INCH DIMENSIONS

ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE

ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN

24-Lead Ceramic DIP (D-24)

SEATING

PLANE

0.023 (0.58)

0.014 (0.36)

0.075 (1.91)

0.015 (0.38)

0.225 (5.72)

MAX

0.200 (5.08)

0.120 (3.05)

0.070 (1.78)

0.030 (0.76)

0.150

(3.81)

MIN

1.290 (32.77) MAX

24

112

13

0.610 (15.49)

0.500 (12.70)

PIN 1

0.098 (2.49) MAX

0.005 (0.13) MIN

0.620 (15.75)

0.590 (14.99)

0.015 (0.38)

0.008 (0.20)

NOTES

1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE.

2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY.

3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE.

4. THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN.

5. APPLIES TO ALL FOUR CORNERS.

6. ALL LEADS — INCREASE MAXIMUM LIMIT BY 0.003" (0.08 mm) MEASURED AT THE CENTER OF THE FLAT,

WHEN HOT SOLDER DIP LEAD FINISH IS APPLIED.

7. TWENTY TWO SPACES.

8. CONTROLLING DIMENSIONS ARE IN MILLIMETERS. INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER

EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN

SEE NOTE 5

SEE NOTE 1

SEE NOTE 7

SEE NOTE 3

SEE NOTE 2, 6

SEE NOTE 4

0.110 (2.79)

0.090 (2.29)

SEE NOTE 4

SEE NOTE 6

Table V. External Op Amp Voltage Mode Connections

Output

Digital

Connect

Connect

Connect

Connect

Range

Input Codes

A to

Pin 17 to

Pin 19 to

Pin 16 to

±10 V

COB or CTC

19

15

A

24

±5 V

COB or CTC

18

15

NC

24

±2.5 V

COB or CTC

18

15

15

24

0 V to 10 V

CSB

18

21

NC

24

0 V to 5 V

CSB

18

21

15

24