AM29LL800BB-150SC datasheet(14/40 Pages) AMD

14 / 40 page

Am29LL800B

ADV ANCE

I N FO RMAT I O N

The reset command may be written between the se-

quence cycles in an erase command sequence before

erasing begins. This resets the device to reading array

data. Once erasure begins, however, the device ig-

nores reset commands until the operation is complete.

The reset command may be written between the se-

quence cycles in a program command sequence be-

fore programming begins. This resets the device to

reading array data (also applies to programming in

Erase Suspend mode). Once programming begins,

however, the device ignores reset commands until the

operation is complete.

The reset command may be written between the se-

quence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must

be written to return to reading array data (also applies

to autoselect during Erase Suspend).

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to read-

ing array data (also applies during Erase Suspend).

Autoselect Command Sequence

The autoselect command sequence allows the host

system to access the manufacturer and devices codes,

and determine whether or not a sector is protected.

Table 5 shows the address and data requirements. This

method is an alternative to that shown in Table 4, which

is intended for PROM programmers and requires VID

on address bit A9.

The autoselect command sequence is initiated by writ-

ing two unlock cycles, followed by the autoselect com-

mand. The device then enters the autoselect mode,

and the system may read at any address any number

of times, without initiating another command sequence.

A read cycle at address XX00h retrieves the manufac-

turer code. A read cycle at address XX01h in word

mode (or 02h in byte mode) returns the device code. A

read cycle containing a sector address (SA) and the

address 02h in word mode (or 04h in byte mode) re-

turns 01h if that sector is protected, or 00h if it is unpro-

tected. Refer to Tables 2 and 3 for valid sector

addresses.

The system must write the reset command to exit the

autoselect mode and return to reading array data.

Word/Byte Program Command Sequence

The system may program the device by word or byte,

depending on the state of the BYTE# pin. Program-

ming is a four-bus-cycle operation. The program com-

mand sequence is initiated by writing two unlock write

cycles, followed by the program set-up command. The

program address and data are written next, which in

turn initiate the Embedded Program algorithm. The

system is

not required to provide further controls or tim-

ings. The device automatically generates the program

pulses and verifies the programmed cell margin. Table

5 shows the address and data requirements for the

byte program command sequence.

When the Embedded Program algorithm is complete,

the device then returns to reading array data and ad-

dresses are no longer latched. The system can deter-

mine the status of the program operation by using DQ7,

DQ6, or RY/BY#. See “Write Operation Status” for in-

formation on these status bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program-

ming operation. The Byte Program command se-

quence should be reinitiated once the device has reset

to reading array data, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from a “0” back to a “1”. Attempting to do so may halt

the operation and set DQ5 to “1”, or cause the Data#

Polling algorithm to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0”. Only erase operations can convert a “0”

to a “1”.

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes or words to the device faster than using the

standard program command sequence. The unlock by-

pass command sequence is initiated by first writing two

unlock cycles. This is followed by a third write cycle

containing the unlock bypass command, 20h. The de-

vice then enters the unlock bypass mode. A two-cycle

unlock bypass program command sequence is all that

is required to program in this mode. The first cycle in

this sequence contains the unlock bypass program

command, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. Table 5 shows the requirements for the com-

mand sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. The first cycle must contain the data

90h; the second cycle the data 00h. The device then re-

turns to reading array data.

Figure 4 illustrates the algorithm for the program oper-

ation. See the Erase/Program Operations table in “AC

Characteristics” for parameters, and to Figure 18 for

timing diagrams.

AM29LL800BB-150SC 数据表(PDF) 14 Page - Advanced Micro Devices

AM29LL800BB-150SC 数据表(HTML) 14 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

数据表下载

链接网址

AM29LL800BB-150SC 数据表(PDF) 14 Page - Advanced Micro Devices

AM29LL800BB-150SC 数据表(HTML) 14 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

数据表 下载

链接网址

数据表下载