Data Sheet

ADV7614

Rev. C | Page 11 of 20

Pin No.

Mnemonic

Type

Description

D11

CVDD

Power

Comparator Supply Voltage (1.8 V).

D12

DDCB_SDA

HDMI input

HDCP Slave Serial Data Port B. DDCB_SDA is a 3.3 V input that is 5 V tolerant.

D13

DDCB_SCL

HDMI input

HDCP Slave Serial Clock Port B. DDCB_SCL is a 3.3 V input that is 5 V tolerant.

D14

DDCA_SCL

HDMI input

HDCP Slave Serial Clock Port A. DDCA_SCL is a 3.3 V input that is 5 V tolerant.

D15

DDCA_SDA

HDMI input

HDCP Slave Serial Data Port A. DDCA_SDA is a 3.3 V input that is 5 V tolerant.

D16

TVDD

Power

Terminator Supply Voltage (3.3 V).

D17

RXA_0+

HDMI input

Digital Input Channel 0 True of Port A in the HDMI Interface.

D18

RXA_0−

HDMI input

Digital Input Channel 0 Complement of Port A in the HDMI Interface.

E1

DE

Digital video output

Data Enable. DE is a signal that indicates active pixel data.

E2

CEC

Digital I/O

Consumer Electronic Control Channel.

E3

NC

No connect

Do Not Connect.

E4

NC

No connect

Do Not Connect.

E15

GND

Ground

Ground.

E16

GND

Ground

Ground.

E17

RXA_C+

HDMI input

Digital Input Clock True of Port A in the HDMI Interface.

E18

RXA_C−

HDMI input

Digital Input Clock Complement of Port A in the HDMI Interface.

F1

HS

Digital video output

Horizontal Synchronization Output Signal in the HDMI Processor.

F2

VS_FIELD

Digital video output

VS is a vertical synchronization output signal in the HDMI processor. FIELD is a

field synchronizationoutput signal in all interlaced video modes. VS or FIELD

can be configured for this pin.

F3

EP_MISO

Digital input

SPI Master Input/Slave Output for External EDID Interface.

F4

EP_MOSI

Digital output

SPI Master Output/Slave Input for External EDID Interface.

F15

GND

Ground

Ground.

F16

CVDD

Power

Comparator Supply Voltage (1.8 V).

F17

TVDD

Power

Terminator Supply Voltage (3.3 V).

F18

GND

Ground

Ground.

G1

P1

Digital video output

Video Pixel Output Port.

G2

P0

Digital video output

Video Pixel Output Port.

G3

EP_CS

Digital output

SPI Chip Select for External EDID Interface.

G4

EP_SCK

Digital output

SPI Clock for External EDID Interface.

G7

GND

Ground

Ground.

G8

GND

Ground

Ground.

G9

GND

Ground

Ground.

G10

GND

Ground

Ground.

G11

PVDD

Power

PLL Supply Voltage (1.8 V).

G12

PVDD

Power

PLL Supply Voltage (1.8 V).

G15

NC

No connect

Do Not Connect.

G16

NC

No connect

Do Not Connect.

G17

TEST1

Test

Connect to GND through a 10 kΩ resistor.

G18

TEST2

Test

Connect to GND through a 10 kΩ resistor.

H1

P3

Digital video output

Video Pixel Output Port.

H2

P2

Digital video output

Video Pixel Output Port.

H3

NC

No connect

Do Not Connect.

H4

NC

No connect

Do Not Connect.

H7

GND

Ground

Ground.

H8

GND

Ground

Ground.

H9

GND

Ground

Ground.

H10

GND

Ground

Ground.

H11

GND

Ground

Ground.

H12

GND

Ground

Ground.

H15

XTALP

Miscellaneousanalog

This is the input pin for the 28.6363 MHz crystal, or it can be overdriven by an

external 1.8 V, 28.6363 MHz clock oscillator source to clock the ADV7614. A

crystal frequency of 24.576 MHz is also supported.

H16

PVDD

Power

PLL Supply Voltage (1.8 V).