STM32F103RG datasheet(91/120 Pages) STMICROELECTRONICS

91 / 120 page

STM32F103xF, STM32F103xG

Electrical characteristics

Doc ID 16554 Rev 3

91/120

5.3.17

Communications interfaces

2C interface characteristics

Unless otherwise specified, the parameters given in Table 54 are derived from tests

performed under ambient temperature, fPCLK1 frequency and VDD supply voltage conditions

summarized in Table 10.

The STM32F103xC, STM32F103xD and STM32F103xESTM32F103xF and STM32F103xG

performance line I

2C interface meets the requirements of the standard I2C communication

protocol with the following restrictions: the I/O pins SDA and SCL are mapped to are not

“true” open-drain. When configured as open-drain, the PMOS connected between the I/O

pin and VDD is disabled, but is still present.

The I

2C characteristics are described in Table 54. Refer also to Section 5.3.14: I/O port

characteristics for more details on the input/output alternate function characteristics (SDA

and SCL).

Table 54.

I2C characteristics

Symbol

Parameter

Standard mode I2C(1)

Guaranteed by design, not tested in production.

Fast mode I2C(1)(2)

fPCLK1 must be at least 2 MHz to achieve standard mode I

2C frequencies. It must be at least 4 MHz to

achieve the fast mode I2C frequencies and it must be a multiple of 10 MHz in order to reach the I2C fast

mode maximum clock speed of 400 kHz.

Unit

Min

Max

Min

Max

tw(SCLL)

SCL clock low time

4.7

1.3

µs

tw(SCLH)

SCL clock high time

4.0

0.6

tsu(SDA)

SDA setup time

250

100

th(SDA)

SDA data hold time

0(3)

The maximum hold time of the Start condition has only to be met if the interface does not stretch the low

period of SCL signal.

-0(4)

The device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the

undefined region of the falling edge of SCL.

900(3)

tr(SDA)

tr(SCL)

SDA and SCL rise time

1000

20 + 0.1Cb

300

tf(SDA)

tf(SCL)

SDA and SCL fall time

300

th(STA)

Start condition hold time

4.0

0.6

µs

tsu(STA)

Repeated Start condition

setup time

4.7

0.6

tsu(STO)

Stop condition setup time

4.0

0.6

μs

tw(STO:STA)

Stop to Start condition time

(bus free)

4.7

1.3

μs

Capacitive load for each bus

line

400

STM32F103RG 数据表(PDF) 91 Page - STMicroelectronics

STM32F103RG 数据表(HTML) 91 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载