| 数据搜索系统,热门电子元器件搜索 |
|
AS7620 数据表(PDF) 9 Page - ams AG |
|
|
|||||||||||||||||||||||||||||
AS7620 数据表(HTML) 9 Page - ams AG |
|
9 / 16 page ![]() www.ams.com/DC-DC_Step-Up/AS7620 Revision 1.18 9 - 16 AS7620 Datasheet - D e t a i l e d D e s c r i p t i o n 8.4 VOUT Selection The AS7620-B features a 3.3V fixed output voltage. The AS7620-A provides an adjustable output from 1.2V (VREF) up to virtually VIN (see 100% Duty Cycle Operation on page 11). To select the desired VOUT, the related resistor divider has to be tuned according to the following formula: (EQ 1) Where: Rh is the high side resistor of the output divider Rl is the resistor of the output divider Note: It is suggested to select resistors in the range of hundreds of k Ω in order to limit the current consumption. 8.5 Current Limit The current is sensed during the on time of the internal PMOS. Three different current limit thresholds can be selected by the ILIM pin: 1. 240mA (typ) ILIM shorted to GND 2. 720mA (typ) ILIM shorted to VOUT (from 1.5V to 3.6V) 3. 1000mA (typ) ILIM floating This threshold is intended as peak current limit. If the current reaches the threshold during the on time, the PMOS is turned off and it will be turned on again only when the current approaches 0A and the feedback voltage is equal or lower than VREF. The maximum output current is ILIM/2. 8.6 Switching Frequency The switching frequency (fsw) changes according to the application conditions and, in particular, to the output current in order to optimize the efficiency in any load condition. Anyway, it is always possible to estimate the fsw during the design process. As described in the Regulation (refer to page 8) – the converter always works in DCM and, normally, the peak current into the inductor is the CL threshold (ILIM). The average of the inductor current must be equal to the output current. The following formula provides the relationship between inductor current and output current: IOUT = (EQ 2) Consequently, the fsw can be expressed as following: (EQ 3) Figure 18. Chart Illustrating the Fsw vs. IOUT in a Standard Application (VIN=24V, VOUT=3.3V, L=10µH, ILIM=1A) V OUT V REF 1 Rh Rl ------- + • = 1 Tsw ---------- 1 2 --- ILIM 2 L • V IN • V IN V OUT – ( ) V OUT • -------------------------------------------------- • • Fsw 2 I OUT • V IN V OUT – ( ) V OUT • • ILIM 2 L • V IN • ---------------------------------------------------------------------------- = Fsw vs. Iout 0 50 100 150 200 250 300 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Iout (A) |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |