I2CSTAT datasheet(123/210 Pages) MICROCHIP

123 / 210 page

DS70139G-page 123

dsPIC30F2011/2012/3012/3013

17.0

SYSTEM INTEGRATION

There are several features intended to maximize

system reliability, minimize cost through elimination of

external components, provide Power Saving Operating

modes and offer code protection:

• Oscillator Selection

• Reset

- Power-on Reset (POR)

- Power-up Timer (PWRT)

- Oscillator Start-up Timer (OST)

- Programmable Brown-out Reset (BOR)

• Watchdog Timer (WDT)

• Low-Voltage Detect

• Power-Saving Modes (Sleep and Idle)

• Code Protection

• Unit ID Locations

• In-Circuit Serial Programming (ICSP)

dsPIC30F devices have a Watchdog Timer which is

permanently enabled via the Configuration bits or can

be software controlled. It runs off its own RC oscillator

for added reliability. There are two timers that offer

necessary delays on power-up. One is the Oscillator

Start-up Timer (OST), intended to keep the chip in

Reset until the crystal oscillator is stable. The other is

the Power-up Timer (PWRT) which provides a delay on

power-up only, designed to keep the part in Reset while

the power supply stabilizes. With these two timers

on-chip, most applications need no external Reset

circuitry.

Sleep mode is designed to offer a very low current

Power-Down mode. The user can wake-up from Sleep

through external Reset, Watchdog Timer Wake-up, or

through an interrupt. Several oscillator options are also

made available to allow the part to fit a wide variety of

applications. In the Idle mode, the clock sources are

still active but the CPU is shut-off. The RC oscillator

option saves system cost while the LP crystal option

saves power.

17.1

Oscillator System Overview

The dsPIC30F oscillator system has the following

modules and features:

• Various external and internal oscillator options as

clock sources

• An on-chip PLL to boost internal operating

frequency

• A clock switching mechanism between various

clock sources

• Programmable clock postscaler for system power

savings

• A Fail-Safe Clock Monitor (FSCM) that detects

clock failure and takes fail-safe measures

• Clock Control register (OSCCON)

• Configuration bits for main oscillator selection

Configuration bits determine the clock source upon

Power-on Reset (POR) and Brown-out Reset (BOR).

Thereafter, the clock source can be changed between

permissible clock sources. The OSCCON register

controls the clock switching and reflects system clock

related status bits.

Table 17-1 provides a summary of the dsPIC30F

Oscillator Operating modes. A simplified diagram of the

oscillator system is shown in Figure 17-1.

Note:

This data sheet summarizes features of

this group of dsPIC30F devices and is not

intended to be a complete reference

source. For more information on the CPU,

peripherals,

descriptions

and

general device functionality, refer to the

“dsPIC30F Family Reference Manual”

(DS70046). For more information on the

device instruction set and programming,

refer to the “16-bit MCU and DSC

Programmer’s

Reference

Manual”

(DS70157).

I2CSTAT 数据表(PDF) 123 Page - Microchip Technology

I2CSTAT 数据表(HTML) 123 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载