Model

Number

Input

Reflected

Ripple

Current

(mA, Typ)

Output

Over

Voltage

Protection

(VDC)

Efficiency

(%, Typ)

Capacitive

Load

(µF Max)

Fuse Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

B3001RW

24

18.0 - 36.0

744

50

100

2.5

6,000.0

0.0

3.0

84

6,800

3,000

B3002RW

24

18.0 - 36.0

959

50

100

3.3

6,000.0

0.0

3.9

86

6,800

3,000

B3003RW

24

18.0 - 36.0

1,185

70

100

5.0

5,000.0

0.0

6.8

88

6,800

3,000

B3004RW

24

18.0 - 36.0

1,420

20

100

12.0

2,500.0

166.0

15.0

88

680

3,000

B3005RW

24

18.0 - 36.0

1,420

20

100

15.0

2,000.0

133.0

18.0

88

680

3,000

B3011RW

48

36.0 - 75.0

372

40

30

2.5

6,000.0

0.0

3.0

84

6,800

1,500

B3012RW

48

36.0 - 75.0

480

40

30

3.3

6,000.0

0.0

3.9

86

6,800

1,500

B3013RW

48

36.0 - 75.0

604

50

30

5.0

5,000.0

0.0

6.8

88

6,800

1,500

B3014RW

48

36.0 - 75.0

710

10

30

12.0

2,500.0

166.0

15.0

88

680

1,500

B3015RW

48

36.0 - 75.0

710

10

30

15.0

2,000.0

133.0

18.0

88

680

1,500

Model Selection Guide

Notes:

1. An internal filter that complies with EN55022 Class“A”is available.Add a suffix“-F”to the model number

1. When measuring output ripple, it is recommended that an external 1.0 µF ceramic capacitor be placed

from the +Vout pin to the -Vout pin. An internal filter Complies with EN55022 Class “A”

2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.

3. The maximum control current at the on/off pin (pin 3) during a logic high is 5 µA. The maximum control

current to the on/off pin at logic low is -100 µA. If the on/off pin is left open, the unit operates. If it is

grounded, the unit will shut off.

4. Operation at no-load will not damage these units. However, they may not meet all specifications.

5. The converter should be connected to a low ac-impedance source.An input source with a highly inductive

impedance may affect the stability of the converter. In applications where the converter output loading is

high and input power is supplied over long lines, it may be necessary to use a capacitor (such as a low

ESR 10.0 µF) on the input to insure start-up.

6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above

for the correct rating.

For continuous UP/Down trimming capability, connect a 10 kW poten-

tiometer between the plus and minus outputs with the wiper arm con-

nected to the V

OUT

trim pin.The trim pin may be left floating if it is not used.

An external resistor may also be used to adjust the converter output.

To adjust the output UP, connect a 5%, 3W resistor between the minus

output pin and the Vout trim pin. The output voltage is increased per

the equation:

R

UP

=

(33 x V

OUT

) - (30 x V

ADJ

)

V

ADJ

- V

OUT

To adjust the output DOWN, connect a 5%, 3W resistor between the

plus output pin and the V

OUT

trim pin. The output voltage is decreased

per the equation:

R

Dwn

=

(36.667 x V

ADJ

) - (33 x V

OUT

)

V

OUT

- V

ADJ

External Trim

Where:

V

OUT

=

Nominal Output Voltage

V

ADJ

=

Adjusted Output Volatage

Units =

VDC / k



Mechanical Dimensions

Heatsink Notes:

range by approximately 10°C.

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Pin Function

1+Vin

2-Vin

3

ON/OFF

4

+Vout

5

-Vout

6

Trim

Pin

Connections

For heatsink option, add suffix “H” to model number (i.e. B3003RU-H)

www.micropowerdirect.com

For Remote Control option, add suffix “R” to model number (i.e. B3003RU-R)

Mechanical Notes:

Derating Curve

For Class “A” filter option, add suffix “F” to model number (i.e. B3003RU-F)