Notes:

side of the unit

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

DM101E

5

4.5 - 5.5

273

30

5.0

200.0

20.0

15

73

500

DM102E

5

4.5 - 5.5

270

30

12.0

83.0

9.0

15

74

500

DM103E

5

4.5 - 5.5

263

30

15.0

67.0

7.0

15

76

500

DM104E

5

4.5 - 5.5

278

30

±5.0

±100.0

±10.0

15

72

500

DM105E

5

4.5 - 5.5

256

30

±12.0

±42.0

±5.0

15

78

500

DM106E

5

4.5 - 5.5

256

30

±15.0

±33.0

±4.0

15

78

500

DM111E

12

10.8 - 13.2

107

15

5.0

200.0

20.0

15

78

200

DM112E

12

10.8 - 13.2

103

15

12.0

83.0

9.0

15

81

200

DM113E

12

10.8 - 13.2

105

15

15.0

67.0

7.0

15

79

200

DM114E

12

10.8 - 13.2

114

15

±5.0

±100.0

±10.0

15

73

200

DM115E

12

10.8 - 13.2

105

15

±12.0

±42.0

±5.0

15

79

200

DM116E

12

10.8 - 13.2

105

15

±15.0

±33.0

±4.0

15

79

200

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

5

No Pin

Common

2

-Vin

-Vin

6

+Vout

+Vout

4

-Vout

-Vout

Derating Curve

g

Notes:

1. Output load regulation is specified for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However,

when measuring output ripple, it is recommended that an external ce-

ramic capacitor be placed from the +Vout pin to the -Vout pin for single

output units and from each output to common for dual output units. An

input capacitor will enhace stability over temperature and input line

variations. Recommended capacitor values are given in the table above.

For applications requiring very low output noise levels, a simple LC filter

should be effective.

4. Dual output units may be connected to provide a 10V, 24V or 30 VDC

output. To do this, connect the load across the positive (+Vout) and

negative (-Vout) outputs and float the output common

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 µF

5 VDC 10.0 µF

4.7 µF

12 VDC

2.2 µF

12 VDC 2.2 µF

1.0 µF

15 VDC 1.0 µF

0.47 µF

Model Selection Guide

Mechanical Dimensions

Pin Connections

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

www.micropowerdirect.com