Notes:

Model

Number

Input

Output

Efficiency

(%, Typ)

Capacitive

Load

(µF Max)

Fuse Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

I2001RU

24

9.0 - 36.0

1,390

80

3.3

4,500

0

87

10,300

4,000

I2002RU

24

9.0 - 36.0

1,852

90

5.0

4,000

0

89

6,800

4,000

I2003RU

24

9.0 - 36.0

1,877

40

12.0

1,670

0

89

1,200

4,000

I2004RU

24

9.0 - 36.0

1,882

40

15.0

1,340

0

89

750

4,000

I2005RU

24

9.0 - 36.0

1,877

40

±12.0

±835

±60

89

±680

4,000

I2006RU

24

9.0 - 36.0

1,882

40

±15.0

±670

±50

89

±380

4,000

I2011RU

48

18.0 - 75.0

695

40

3.3

4,500

0

88

10,300

2,000

I2012RU

48

18.0 - 75.0

926

45

5.0

4,000

0

89

6,800

2,000

I2013RU

48

18.0 - 75.0

938

25

12.0

1,670

0

89

1,200

2,000

I2014RU

48

18.0 - 75.0

930

25

15.0

1,340

0

89

750

2,000

I2015RU

48

18.0 - 75.0

938

25

±12.0

±835

±60

89

±680

2,000

I2016RU

48

18.0 - 75.0

941

25

±15.0

±670

±50

89

±380

2,000

Derating Curve

Notes:

1. Output ripple is measured with a 1.0 µF ceramic and a 10 µF tantalum

capcitor connected across the outputs.

2. Transient recovery is measured to within a 1% error band for a load step change

of 75% to 100%.

3. Operation at no-load will not damage the unit, but they may not meet

all specifications.

4. The On/Off Control input (Pin 3)

is referenced to -Vin (Pin 2). If

it is not used, the control pin

should be left open. If the pin

turn off.

5. An external resistor may be used

to adjust the converter output by ±10%.To adjust the output UP, connect a 5%,

3W resistor between the minus output pin and the Vout trim pin. To adjust the

output DOWN, connect a 5%, 3W resistor between the plus output pin and

the V

OUT

trim pin. For continuous UP/Down trimming capability, connect a 10

kW potentiometer between the plus and minus outputs with the wiper arm

connected to the V

OUT

trim pin.The trim pin may be left floating if it is not used.

Contact the factroy for more information.

6. It is recommended that a fuse be used on the input of a power supply

for protection. See the Model Selection table above for the correct rating.

www.micropowerdirect.com

Pin

Single

Dual

1

+Vin

+Vin

2

-Vin

-Vin

3

Remote ON/OFF

4

+Vout

+Vout

5

Trim

Common

6

-Vout

-Vout

Pin Connections

Model Selection Guide

Mechanical Dimensions

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Min

Max

On

3.5 VDC

12 VDC

Off

0.0 VDC

1.2 VDC

In. Current (on)

0.5 mA

In. Current (off)

-0.5 mA