E2EZ

3

Ratings and Specifications

*1. Use the Sensor within the range in which the green indicator is ON.

*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and

a set distance of half the sensing distance.

Model E2EZ-X2D

@-N

E2EZ-X2D

@-M1J

E2EZ-X2D

@-M1GJ

E2EZ-X4D

@-N

E2EZ-X4D

@-M1J

E2EZ-X4D

@-M1GJ

E2EZ-X8D

@-N

E2EZ-X8D

@-M1J

E2EZ-X8D

@-M1GJ

E2EZ-X4C1

E2EZ-X4Y1

E2EZ-X8C1

E2EZ-X8Y1

Item

Sensing distance

2 mm

±10%

4 mm

±10%

8 mm

±10%

4 mm

±10%

8 mm

±10%

0 to 1.6 mm

0 to 3.2 mm

0 to 6.4 mm

0 to 3.2 mm

0 to 6.4 mm

Differential travel

20% max. of sensing distance

Detectable object

Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)

Standard sensing

object

Iron, 12

× 12 × 1 mm

Iron, 30

× 30 × 1 mm

Iron, 54

× 54 × 1 mm

Iron, 30

× 30 × 1 mm

Iron, 54

× 54 × 1 mm

Response

200 Hz

100 Hz

30 Hz

C Models: 12 Hz

Y Models: 5 Hz

C Models: 8 Hz

Y Models: 5 Hz

Power supply volt-

age

(operating voltage

range)

12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.

C Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p):

10% max.

Y Models: 100 to 220 VAC (90 to 250 VAC), 50/60 Hz

Current

consumption

---

C Models: 15 mA max.

Leakage current

0.8 mA max.

Y Models: 2 mA max. at 100 VAC, 3 mA max. at 200 VAC

Con-

trol

output

Load cur-

rent

3 to 100 mA max.

C Models: NPN open-collector output

100 mA max. at 12 VDC (30 VDC max.)

200 mA max. at 24 VDC (30 VDC max.)

Y Models: 10 to 200 mA

Residual

voltage

3 V max. (Load current: 100 mA, Cable length: 2 m)

C Models: 2 V max. (Load current: 200 mA, Cable length:

2 m)

Y Models: Refer to residual voltage characteristic data

Refer to page 4.

Indicators

D1 Models: Operation indicator (red), Setting indicator (green)

D2 Models: Operation indicator (red)

C Models: Detection indicator (red)

Y Models: Operation indicator (red)

Operation mode

(with sensing ob-

ject approaching)

D1 Models: NO

D2 Models: NC

For details, refer to the Timing chart on page 5.

NO

For details, refer to the Timing chart on page 6.

Protection

circuits

Load short-circuit protection, Surge suppressor

C Models: Load short-circuit protection, Reverse polarity

protection, Surge suppressor

Y Models: Surge suppressor

Ambient

temperature range

Operating/Storage: 0 to 50

°C (with no icing or condensation)

Ambient

humidity range

Operating/Storage: 35% to 95% (with no condensation)

Temperature

influence

±20% max. of sensing distance at 23°C in the temperature range of 0 to 50°C

Voltage influence

±2.5% max. of sensing distance at rated voltage in the rated voltage ±10% range

Insulation

resistance

50 M

Ω min. (at 500 VDC) between current-carrying parts and case

Dielectric strength

1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case

C Models: 1,000 VAC, 50/60 Hz for 1 min between cur-

rent-carrying parts and case

Y Models: 2,000 VAC, 50/60 Hz for 1 min between cur-

rent-carrying parts and case

Vibration

resistance

Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance

Degree of

protection

IEC 60529 IP67, in-house standards: oil-resistant

Connection

method

Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models

Weight

(packed state)

E2EZ-X2D

@-N: Approx.

70 g

E2EZ-X2D

@-M1J: Approx.

40 g

E2EZ-X2D

@-M1GJ:

Approx. 40 g

E2EZ-X4D

@-N: Approx.

160 g

E2EZ-X4D

@-M1J:

Approx. 90 g

E2EZ-X4D

@-M1GJ:

Approx. 90 g

E2EZ-X8D

@-N: Approx.

220 g

E2EZ-X8D

@-M1J:

Approx. 160 g

E2EZ-X8D

@-M1GJ:

Approx. 160 g

Approx. 170 g

Approx. 270 g

Materi-

als

Case

Nickel-plated brass

Sensing

surface

PBT

Heat-resistant ABS

Clamp-

ing nuts

Zinc-plated iron

Toothed

washer

Zinc-plated iron

Accessories

Instruction manual