CS82C85 datasheet(10/21 Pages) INTERSIL

10 / 21 page

306

Absolute Maximum Ratings

Thermal Information

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V

Input, Output or I/O Voltage . . . . . . . . . . . GND -0.5V to VCC +0.5V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1

Operating Conditions

Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V

Operating Temperature Range

C82C85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to +70oC

I82C85 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC

M82C85 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC

Thermal Resistance (Typical)

θJA (oC/W) θJC (oC/W)

CERDIP Package . . . . . . . . . . . . . . . . .

CCC Package . . . . . . . . . . . . . . . . . . . .

PLCC Package . . . . . . . . . . . . . . . . . . .

N/A

Storage Temperature Range . . . . . . . . . . . . . . . . .-65oC to +150oC

Maximum Junction Temperature Ceramic Package . . . . . . . +175oC

Maximum Junction Temperature Plastic Package . . . . . . . . +150oC

(Soldering 10s)

Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . +300oC

(PLCC - Lead Tips Only)

Die Characteristics

Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 Gates

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

DC Electrical Specifications VCC = 5.0V 10%; TA = 0

oC to +70oC (C82C85);

TA = -40

oC to +85oC (I82C85);

TA = -55

oC to +125oC (M82C85)

SYMBOL

PARAMETER

MIN

MAX

UNITS

TEST CONDITIONS

VIH

Logical One Input Voltage

2.0

2.2

-V

C82C85, I82C85

M82C85

VIHR

Reset Input High Voltage

2.8

VIL

Logical Zero Input Voltage

0.8

Note 1

VT+ - VT

Reset Input Hysteresis

0.25

VOH

Logical One Output Voltage

VCC-0.4

IOH = -5.0 mA (CLK, CLK50)

IOH = -1.0mA (X2)

IOH = -2.5mA (all other outputs)

VOL

Logical Zero Output Voltage

0.4

IOL = +2.5mA (X2)

IOL = +5.0mA (all other outputs)

Input Leakage Current

-1.0

1.0

µAVIN = VCC or GND, except DIP

Pins 11 - 15, 21, 23

IBHH

Bus-hold High Leakage Current

-10

-200

µAVIN = 3.0V; Pins 11 - 15, 21

ICCSB

Standby Power Supply Current

100

µA

82C85 in HALT state with oscillator

stopped

ICCOP

Operating Power Supply Current

Crystal Frequency = 15MHz, outputs

open, inputs = GND or VCC

Crystal Frequency = 25MHz, outputs

open, inputs = GND or VCC

ICCSLOW

Slow Mode Operating Current

mA Crystal

Freq = 15MHz

Outputs Open; SLO/FST = GND,

START = VCC, Other inputs - VIN =

VCC or GND

mA Crystal

Freq = 25MHz

NOTE:

1. For CSYNC, VIL = GND

Capacitance

TA = 25

SYMBOL

PARAMETER

TYPICAL

UNITS

TEST CONDITIONS

CIN

Input Capacitance

FREQ = 1MHz, all measurements are referenced to device

GND

COUT

Output Capacitance

82C85

CS82C85 数据表(PDF) 10 Page - Intersil Corporation

CS82C85 数据表(HTML) 10 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

数据表下载