DG408DJ datasheet(4/16 Pages) INTERSIL

4 / 16 page

Absolute Maximum Ratings

Thermal Information

V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V

GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25V

Digital Inputs, VS, VD (Note 3). . . . . .(V-) -2V to (V+) + 2V or 20mA,

Whichever Occurs First

Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA

Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Thermal Resistance (Typical, Note 4)

θJA (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 125oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

3. Signals on SX, DX, EN or AX exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations

Test Conditions: V+ = +15V, V- = -15V, VAL = 0.8V, VAH = 2.4V, Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

TEMP (oC)

(NOTE 5)

MIN

(NOTE 6)

TYP

(NOTE 5)

MAX

UNITS

DYNAMIC CHARACTERISTICS

Transition Time, tTRANS

(See Figure 1)

Full

160

250

Break-Before-Make Interval, tOPEN

(See Figure 3)

Enable Turn-ON Time, tON(EN)

(See Figure 2)

115

150

Full

225

Enable Turn-OFF Time, tOFF(EN)

(See Figure 2)

Full

105

150

Charge Injection, Q

CL = 10nF, VS = 0V

OFF Isolation

VEN = 0V, RL = 1kΩ,

f = 100kHz (Note 9)

-75

Logic Input Capacitance, CIN

f = 1MHz

Source OFF Capacitance, CS(OFF)

VEN = 0V, VS = 0V,

f = 1MHz

Drain OFF Capacitance, CD(OFF)

VEN = 0V, VD = 0V,

f = 1MHz

DG408

DG409

Drain ON Capacitance, CD(ON)

VEN = 3V, VD = 0V,

f = 1MHz, VA = 0V or 3V

DG408

DG409

DIGITAL INPUT CHARACTERISTICS

Logic Input Current,

Input Voltage High, IAH

VA = 2.4V, 15V

Full

-10

µA

Logic Input Current,

Input Voltage Low, IAL

VEN = 0V, 2.4V,

VA = 0V

Full

-10

µA

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

Full

-15

Drain-Source ON Resistance,

rDS(ON)

VD = ±10V, IS = -10mA

(Note 7)

100

Ω

Full

125

Ω

rDS(ON) Matching Between Channels,

∆rDS(ON)

VD = 10V, -10V (Note 8)

Ω

Source OFF Leakage Current, IS(OFF)

VEN = 0V, VS = ±10V,

VD = +10V

-0.5

0.5

Full

-5

DG408, DG409

DG408DJ 数据表(PDF) 4 Page - Intersil Corporation

DG408DJ 数据表(HTML) 4 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表下载

链接网址

DG408DJ 数据表(PDF) 4 Page - Intersil Corporation

DG408DJ 数据表(HTML) 4 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表 下载

链接网址

数据表下载