| 数据搜索系统,热门电子元器件搜索 |
|
AN966 数据表(PDF) 9 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN966 数据表(HTML) 9 Page - STMicroelectronics |
|
9 / 21 page ![]() quency inductor current ripple (twice the average line current, see fig. 9). The worst conditions will occur on the peak of the minimum rated input voltage. The maximum high frequency voltage ripple is usually imposed between 1% and 10% of the minimum rated input voltage. This is expressed by a coefficient r (typically, r = 0.01 to 0.1): Cin = I rms 2 π ⋅ ƒsw ⋅ r ⋅ Virms (min) High values of Cin alleviate the burden to the EMI filter but cause the power factor and the harmonic con- tents of the mains current to worsen, especially at high line and light load. On the other hand, low values of Cin improve power factor and reduce mains current distortion but require heavier EMI filtering and increase power dissipation in the input bridge. It is up to the designer to find the right trade-off in their application. Output Capacitor The output bulk capacitor (Co) selection depends on the DC output voltage, the admitted overvoltage, the output power and the desired voltage ripple. The 100 to 120Hz (twice the mains frequency) voltage ripple ( ∆VO= 1/2 ripple peak-to-peak value) is a function of the capacitor impedance and the peak capacitor current (IC(2f)pk = Io): ∆VO = IO ⋅ √ 1 (2π ⋅ 2f ⋅ CO) 2 + ESR 2 With a low ESR capacitor the capacitive reactance is dominant, therefore: CO ≥ IO 4 π ⋅ f ⋅ ∆VO = PO 4 π ⋅ f ⋅ VO ⋅ ∆VO ∆Vo is usually selected in the range of 1 to 5% of the output voltage. Although ESR usually does not affect the output ripple, it has to be taken into account for power losses calculation. The total RMS capacitor ripple current, including mains frequency and switching frequency components, is: ICrms = √ 32 √2 9 π ⋅ I rms 2 ⋅ Virms Vo − I o 2 If the application has to guarantee a specified hold-up time, the selection criterion of the capacitance will change: Co has to deliver the output power for a certain time (tHold) with a specified maximum dropout voltage: CO = 2 ⋅ PO ⋅ tHold V o_min 2 − V op_min 2 where Vo_min is the minimum output voltage value (which takes load regulation and output ripple into account) and Vop_min is the minimum output operating voltage before the ’power fail’ detection from the downstream system supplied by the PFC. Boost Inductor Designing the boost inductor involves several parameters and different approaches can be used. First, the inductance value must be defined. The inductance (L) is usually determined so that the mini- mum switching frequency is greater than the maximum frequency of the internal starter, to ensure a cor- rect TM operation. Assuming unity PF, it is possible to write: Ton = L ⋅ ILpk ⋅ sin(θ) √2 ⋅ Virms ⋅ sin(θ) = L ⋅ ILpk √2 ⋅ Virms Toff = L ⋅ ILpk ⋅ sin(θ) Vo − √2 ⋅ Virms ⋅ sin(θ) AN966 APPLICATION NOTE 9/21 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |