| 数据搜索系统,热门电子元器件搜索 |
|
AN1060 数据表(PDF) 9 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN1060 数据表(HTML) 9 Page - STMicroelectronics |
|
9 / 11 page ![]() mains frequency. The drawback of primary sensing technique is its poor load regulation, but this is of no concern in this case. The post regulation on the secondary side with the L4955 linear regulator (see Ref. [4] for information) ensures a high accuracy of the end-of-charge output voltage, as well as a precise constant current char- acteristic during battery charge. Additionally, the charge current can be adjusted from 1 to 2 A by means of the 22 k Ω trimmer. The schottky diode in series to the output prevents battery discharge when this is connected and the charger is off. The diode connected between pin 4 and pin 7 of the L4955 and the 220 Ω resistor limit the current flowing in case of reverse battery connection. The same battery charger can be realised without a post-regulator. Such a system is shown in fig. 10. It uses again an isolated feedback with an optocoupler and a secondary side reference/error amplifier, the TSM101, for voltage and current regulation. This device basically incorporates a TL431 and two op-amps with or-ed outputs. One op-amp will be used for constant voltage control and the other one for constant current control. A precise internal cur- rent generator, available at pin 3, can be used to offset the intervention threshold of the constant current regulation. For more details, please refer to Ref. [5]. The voltage generated by the self-supply winding tracks the output voltage, which can be quite low (<9V) when the battery is nearly exhausted. To let the system work even under this condition the self-supply will deliver a voltage above L6561’s UVLO when the output voltage falls to its minimum. As a result, however, when the charger is in voltage regulation (battery disconnected or end-of-charge) the self-sup- ply voltage will exceed the maximum rating of the L6561. This requires the use of a linear regulator (L78L12 in the present case) to limit the excursion of the voltage. The diode in series to the output of the L78L12 prevents current diversion through the regulator at start-up. The switch connected between TSM101’s pin 2 and ground enables/disables the above mentioned inter- nal current reference. If the switch is open, pin 2 is pulled up through the 10 k Ω resistor, the internal cur- rent generator is disabled and the constant current characteristic is set at 2A. If the switch is closed, pin 2 is grounded and the internal current reference will be enabled. Pin 3 will be offset by about 160 mV and the constant current threshold will be set at 0.3A. 2 1 L6561 4 7 3 5 6 8 15 Vdc / 2A 470 nF 3 M Ω 470 k Ω 2xBZW0485 STTA106 47 k Ω 10 Ω 0.5 Ω 20 k Ω 2.4 k Ω 20 k Ω 5.1 k Ω 12 k Ω 4N35 4N35 1 nF 220 nF STP5NA60 STPS8H100D 560 µF 2200 µF BYW 100-200 4 8 2 3 7 6 1 5 560 µF 2.2 k Ω 11 k Ω 100 nF 2.2 µF 1 µF 0.1 Ω TSM 101 4.7 nF DF06M 100 nF 2.2 k Ω 3 2 1 L78L12 10µF 50V 47 µF 130 Ω 1.1 k Ω 1N4148 10 k Ω 2.2 µF 1N4148 1N4148 85 to 270 Vac 2A FUSE TRANSFORMER SPEC: Core E25/13/7, 3C85 grade or equivalent ≈0.7 mm air gap for a primary inductance of 720 µH N1 : 2 series winding, 39 T each, AWG28 ( ∅ 0.37 mm) N2 : 12T, 3xAWG26 ( ∅ 0.40mm) N3 : 25T, AWG31 ( ∅ 0.23 mm) N1 N2 N3 4.7 µF 2200 µF Figure 10. 30W, High-PF battery charger with secondary voltage/current regulation AN1060 APPLICATION NOTE 9/11 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |