| 数据搜索系统,热门电子元器件搜索 |
|
AN1657 数据表(PDF) 5 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN1657 数据表(HTML) 5 Page - STMicroelectronics |
|
5 / 9 page ![]() 5/9 AN1657 APPLICATION NOTE The importance of the circuit lies not only in the reduction of the associated losses from the 240 mW of the resistive start-up to less than 10 mW, but also in the fact that, arranged as a current source like in the schematic of figure 2, it provides constant wake-up and restart times for the converter, regardless of the input AC voltage. The benefits resulting from that will be clearer after discussing how the system handles OFF-mode operation. The current sourced by the generator and that charges the VCC capacitor C3 is: , where VZ is the zener voltage of DZ1, VF the forward drop across D1 and Vth the threshold voltage of Q1. With an appropriate selection of VZ it is possible to compensate the temperature drift of both VF (≈ -2 mV/ °C) and Vth ( ≈ -7 mV/°C). Experience shows that zener diodes with VZ =12V have a temperature coeffi- cient around +10 mV/°C, thus one of them will be selected. With this circuit, neglecting the start-up current absorbed by the L6565, which is typically two orders of magnitude smaller, the wake-up time is defined by R2, C3 and the turn-on threshold (VCCOn) of the L6565: , whereas the restart time, that is the time needed for Vcc to go from the UVLO threshold (VCCOff) to VCCOn during a continuous restart, depends on the VCC hysteresis (VCCHys = VCCOn - VCCOn) of the L6565: . The circuit that is actually responsible for handling OFF-mode operation is on the secondary side and is the network comprising R25 to R27, C18, DZ4 and Q4. To adapt the existent circuit to the new operation, R19 (R16 in the schematic of fig. 1) has been increased to 680 Ω and the capacitor C13 has been replaced by the zener diode DZ3. The bulk capacitor C13 on the +15V line has been increased from 470 to 2200µF and the L7805 replaced by an LE50CZ. During normal operation a logic signal (open collector) governed by the µP keeps the OFF input low, so that Q4 is always off and the OFF-mode circuit is disabled. When the monitor is to enter OFF-mode the µP acts so that the loads of all the outputs are cut off, then it reduces its own consumption and opens the pull-down that was grounding the OFF input. Q4 is immediately turned on because the voltage on the +15V is already higher than threshold (VT) defined by DZ4, R25 and R27. Q4 will then draw a relatively large current from the photodiode, limited by R19+R20 (that is why C13 has been replaced by DZ3: this will still give a high frequency pole to the output-to-control transfer function but will keep the current through the photodiode under control as Q4 is turned on). As a result there will be quite a large current in the phototransistor too, which will bring the voltage on the current sense pin above the 2V threshold that shuts down the driver of the L6565 and stops PWM activity. The IC, however, remains active and pin 2 stays high, thus keeping the start-up generator off as long as Vcc - which is decaying because of the quiescent consumption of the IC and the phototransistor current - is above VCCOff. As VCC = VCCOff the IC turns off, pin 2 goes low and the start-up generator is turned on again. This is the most critical moment: since the output voltage starts from about 15V and needs to decay below VT before Q4 turns off, the phototransistor will keep on sinking quite a large current even after the start- up generator is enabled. As a result, VCC will be pulled well below VCCOff. The start-up generator will take a time longer than TRestart to bring VCC back to VCCOn and restart PWM activity. On the secondary side, as the L6565 stops switching the voltage on C13 starts to decay slowly and goes on like that as long as the L6565 does not switch. Even during this time the voltage on C13 must not go below the minimum value that correctly supplies the linear regulator. To have maximum headroom the LE50CZ has been used, which features less than 0.5V dropout. Besides, this part has lower quiescent current and the low dropout allows keeping a lower average input voltage, which helps reduce the actual load on the converter. As PWM restarts, the voltage on C13 quickly builds up and reaches VT in few milliseconds, which turns on Q4 again restarting another cycle. C18 filters switching noise and allows a clean Q4 turn-on. This time the phototransistor current will drop to zero before Vcc falls below VccOff and there will be no VCC undershoot. I CH V Z V F V th – + R2 ----------------------------------- = T wak e u p – C3 I CH ---------V CCOn ≈ T Res tart C3 I CH ---------V CCHys ≈ |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |