| 数据搜索系统,热门电子元器件搜索 |
|
AN1729 数据表(PDF) 3 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN1729 数据表(HTML) 3 Page - STMicroelectronics |
|
3 / 10 page ![]() 3/10 AN1729 APPLICATION NOTE For further information concerning a QR Flyback converter based on controller L6565 you can refer to the Ap- plication Note AN1326 and to the datasheet of the controller. Standby Consumption Issues When the TV set is in standby we need to supply the micro controller, the LED and the IR receiver for the remote control. This supply voltage can be obtained through a linear voltage regulator from one of the low voltage out- puts of the converter. Under such conditions the load is very light also because we have to consider that the micro controller is in low consumption working mode. Most of power consumption in a lightly loaded switching converter is due to the switching losses, thus the lower the switching frequency the lower the losses. In most of the modern Power Supply circuits, when the converter is very lightly loaded, a low frequency working mode is often used. The switching frequency cannot be too low to avoid audible noise. In order to further lower switching frequency the converter can be operated in a "burst" mode, where there are short periods of time where the MOS switches at the normal operation switching frequen- cy spaced out by long periods of time where the MOS does not switch; in this way the average switching fre- quency can be very low and switching losses can be minimized. Burst-mode operation In a normal converter realized using the L6565 controller, when the load is very light, a burst-mode operation automatically takes place thanks to the "frequency foldback function" (See App. Note AN1326 and the datasheet of the L6565 controller for details). It is important to notice that with this kind of burst- mode operation the control loop is still active and the output voltages are still regulated. In a TV power supply, when the system is in standby mode, generally we do not need to have all the output voltages regulated, we need only to guarantee a minimum voltage at the input of the linear voltage regulator that supplies the micro controller. Moreover, the loss reduction offered by the natural burst-mode described be- fore is not enough to meet the "less than 1 Watt" target in this application. With a simple and low-cost additional circuitry it is possible to have an enhanced burst-mode operation that decreases the average switching frequen- cy to a very low value, hence considerably reducing the total losses in the converter. In that case the regulation loop is skipped but the required minimum voltage at the input of the linear voltage regulator can be guaranteed. Description of the TV Set Power Supply circuit The complete schematic of the realized circuit is shown in figure 3. It is a two output switch mode power supply with a third output for the micro controller, obtained through a voltage regulator (LE50C), from the secondary output (Vout2 =14V). The electrical specification is listed in table 1: Table 1. Input Voltage range 88 to 264 Vac Mains frequency 50-60 Hz Maximum output power 60 W Output voltages Vout1 = 114V; Pout1 = 55 W Vout2 = 14V; Pout2 = 4.2 W Output of the voltage regulator Vout3 =5V; Ioutwup = 70mA; Ioutstand-by=10mA Minimum switching frequency 70 kHz Target efficiency η > 80% Maximum standby consumption (@ 220 Vac) < 1W |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |