数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

AN2044 数据表(PDF) 5 Page - STMicroelectronics

部件名 AN2044
功能描述  OPERATING PRINCIPALS FOR PRACTISPIN
PDF  9 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

AN2044 数据表(HTML) 5 Page - STMicroelectronics

  AN2044 Datasheet HTML 1Page - STMicroelectronics AN2044 Datasheet HTML 2Page - STMicroelectronics AN2044 Datasheet HTML 3Page - STMicroelectronics AN2044 Datasheet HTML 4Page - STMicroelectronics AN2044 Datasheet HTML 5Page - STMicroelectronics AN2044 Datasheet HTML 6Page - STMicroelectronics AN2044 Datasheet HTML 7Page - STMicroelectronics AN2044 Datasheet HTML 8Page - STMicroelectronics AN2044 Datasheet HTML 9Page - STMicroelectronics  
Zoom Inzoom in Zoom Outzoom out
 5 / 9 page
background image
5/9
AN2044 APPLICATION NOTE
Table 1. State Variable Representation
In its simplest form this system executes a trapezoidal move by the following steps:
1) Calculate the motor position values ( P1 and P-P2 using the formulas derived above ) at which
the system should transition from accel to constant speed and then from constant speed to de-
cel.
2) Set the POS and SPD variables to zero, set ACC to the required value, and then start up the
ISR. The ISR will update SPD by adding ACC0 into SPD0, ACC1 into SPD1 (plus a possible
carry from previous), and then inc SPD2 if there was a carry out of ACC1 + SPD1. POS is up-
dated by adding SPD1 into POS0, SPD2 into POS1 (with carry), then inc POS2 if SPD2 + POS1
produced a carry and finally inc POS3 if POS2 rolls over.
3) Whenever POS2 increases (it could never increase by more that 1 because of the small time
tick), advance the motor by one step.
4) When the integer part (POS3: POS2) of POS matches P1, set ACC to zero to enter the constant
velocity region. Speed will hold constant but position will continue to increase.
5) When POS matches P-P2, change the value in ACC from zero to the required decel setting and
start subtracting into SPD instead of adding.
6) When POS matches P, set ACC and SPD to zero ( SPD should already be there ), stop stepping
the motor, and hold position.
In step 3 of the procedure for executing a trapezoidal move it was stated that we must "ad-
vance the motor by one step". Lets examine the details required to accomplish this. First, let's
describe how a bipolar, two phase stepper motor is commutated or stepped.
The motor has two windings (A and B) each of which may be in one of three states: Positive,
Negative, or Off based on the direction of current flow, if any, through the coil. The convention-
al half step commutating sequence is described in figure 4. After step #7 the sequence re-
peats back from 0. Table 2 presents a graphical display of the current in the motor coils vs.
motor step.
Table 2. Half Step Commutating Sequence
POS3
POS2
*
POS1
POS0
*
SPD2
SPD1
SPD0
*
ACC1
ACC0
STEP #
COIL A
COIL B
IN1A
IN2A
ENA
IN1B
IN2B
ENB
0POS
NEG
1
0
1
0
1
1
1POS
ZERO
1
0
1
X
X
0
2POS
POS
1
0
1
1
0
1
3ZERO
POS
X
X
0
1
0
1
4
NEG
POS
0
1
1
1
0
1
5NEG
ZERO
0
1
1
X
X
0
6NEG
NEG
0
1
1
0
1
1
7ZERO
NEG
X
X
0
0
1
1



Html Pages

1 2 3 4 5 6 7 8 9


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com