数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

AN3014 数据表(PDF) 7 Page - STMicroelectronics

部件名 AN3014
功能描述  This application note describes the characteristics and the features
PDF  29 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

AN3014 数据表(HTML) 7 Page - STMicroelectronics

Back Button AN3014 Datasheet HTML 3Page - STMicroelectronics AN3014 Datasheet HTML 4Page - STMicroelectronics AN3014 Datasheet HTML 5Page - STMicroelectronics AN3014 Datasheet HTML 6Page - STMicroelectronics AN3014 Datasheet HTML 7Page - STMicroelectronics AN3014 Datasheet HTML 8Page - STMicroelectronics AN3014 Datasheet HTML 9Page - STMicroelectronics AN3014 Datasheet HTML 10Page - STMicroelectronics AN3014 Datasheet HTML 11Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 29 page
background image
AN3014
Main characteristics and circuit description
Doc ID 16064 Rev 2
7/29
L6599A overload and short-circuit protection
The current into the primary winding is sensed by the lossless circuit R41, C27, D11, D10,
R39, and C25 and is fed to the ISEN pin (pin 6). In case of overcurrent, the voltage on the
pin passes an internal threshold (0.8 V), triggering a protection sequence. The capacitor
(C45) connected to the DELAY pin (pin 2) is charged by an internal 150-µA current
generator and is slowly discharged by the external resistor (R24). If the voltage on the pin
reaches 2 V, the soft-start capacitor is completely discharged so that the switching
frequency is pushed to its maximum value. As the voltage on the pin exceeds 3.5 V, the IC
stops switching and the internal generator is turned off, so that the voltage on the pin decays
due to the external resistor. The IC is soft-restarted as the voltage drops below 0.3 V. In this
way, under short-circuit conditions, the converter works intermittently with very low input
average power.
Overvoltage and open loop protection
Both the PFC and resonant circuit stages are equipped with their own overvoltage
protection.
The PFC controller L6563H monitors its output voltage via the resistor divider connected to
a dedicated pin (PFC_OK, pin 7), protecting the circuit in case of loop failures,
disconnection or deviation from the nominal value of the feedback loop divider. If the voltage
on pin #7 exceeds 2.5 V the IC stops switching and restarts as the voltage on the pin falls
below 2.4 V, preventing the output voltage becoming excessive in case of transient due to
the slow response of the error amplifier. However, if contemporaneously the voltage of the
INV pin falls below 1.66 V (typ.), a feedback failure is assumed. In this case the PFC_OK
circuitry latches the L6563H operations and, by means of the PWM_LATCH pin (pin 8) it
latches the L6599A as well, via the DIS pin (pin 8). The converter is kept latched by the
L6563H HV circuit which supplies the IC, charging the VCC capacitor periodically. To resume
converter operation, mains restart is necessary.
The DIS pin is used to protect also the resonant stage against overvoltage. The Zener diode
D8 detects the auxiliary voltage, which is proportional to the output voltage. In case of loop
failure it conducts and voltage on the DIS pin exceeds the internal threshold, and latches off
the device. L6563H operation is also stopped by the PFC_STOP pin.
Secondary-side synchronous rectification with the SRK2000
The SRK2000 core function is to switch on each synchronous rectifier MOSFET whenever
the corresponding transformer half-winding starts conducting (i.e. when the MOSFET body
diode starts conducting), and then to switch it off when the current flowing through it
approaches zero. For this purpose, the IC is equipped with two pins (DVS1 and DVS2)
capable of sensing the MOSFET drain voltage level.
Standby power saving
The board has a burst-mode function implemented, allowing power saving during light load
operation.
The L6599A STBY pin (pin 5) senses the optocoupler’s collector voltage, which is related to
the feedback control. This signal is compared to an internal reference (1.24 V). If the voltage
on the pin is lower than the reference, the IC enters an idle state and its quiescent current is
reduced. As the voltage exceeds the reference by 50 mV, the controller restarts the
switching. The burst-mode operation load threshold can be programmed by properly
choosing the resistor connecting the optocoupler to the RFMIN pin (R34). On this board, the
controller operates in burst-mode if the load falls below ~10 W.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com