LT1121CS8 datasheet(3/12 Pages) LINER

3 / 12 page

LT1121/LT1121-3.3/LT1121-5

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Load Regulation

LT1121-3.3

∆ILOAD = 1mA to 150mA, TJ = 25°C–12

– 20

∆ILOAD = 1mA to 150mA

–20

– 30

LT1121-5

∆ILOAD = 1mA to 150mA, TJ = 25°C–17

– 30

∆ILOAD = 1mA to 150mA

–28

– 45

LT1121 (Note 4)

∆ILOAD = 1mA to 150mA, TJ = 25°C–12

– 20

∆ILOAD = 1mA to 150mA

–18

– 30

Dropout Voltage

ILOAD = 1mA, TJ = 25°C

0.13

0.16

(Note 5)

ILOAD = 1mA

0.25

ILOAD = 50mA, TJ = 25°C

0.30

0.35

LOAD = 50mA

0.50

ILOAD = 100mA, TJ = 25°C

0.37

0.45

ILOAD = 100mA

0.60

ILOAD = 150mA, TJ = 25°C

0.42

0.55

ILOAD = 150mA

0.70

Ground Pin Current

ILOAD = 0mA

µA

(Note 6)

ILOAD = 1mA

120

µA

ILOAD = 10mA

350

500

µA

ILOAD = 50mA

1.5

2.5

ILOAD = 100mA

4.0

7.0

ILOAD = 150mA

7.0

14.0

Adjust Pin Bias Current (Notes 4, 7)

TJ = 25°C

150

300

Shutdown Threshold

VOUT = Off to On

1.2

2.8

VOUT = On to Off

0.25

0.75

Shutdown Pin Current (Note 8)

VSHDN = 0V

610

µA

Quiescent Current in Shutdown (Note 9)

VIN = 6V, VSHDN = 0V

µA

Ripple Rejection

VIN – VOUT = 1V (Avg), VRIPPLE = 0.5VP-P,50

fRIPPLE = 120Hz, ILOAD = 0.1A

Current Limit

VIN – VOUT = 7V, TJ = 25°C

200

500

Input Reverse Leakage Current

VIN = –20V, VOUT = 0V

1.0

Reverse Output Current (Note 10)

LT1121-3.3

VOUT = 3.3V, VIN = 0V

µA

LT1121-5

VOUT = 5V, VIN = 0V

µA

LT1121 (Note 4)

VOUT = 3.8V, VIN = 0V

µA

ELECTRICAL C

HARA TERISTICS

Note 4: The LT1121 (adjustable version) is tested and specified with the

adjust pin connected to the output pin.

Note 5: Dropout voltage is the minimum input/output voltage required to

maintain regulation at the specified output current. In dropout the output

voltage will be equal to: (VIN – VDROPOUT).

Note 6: Ground pin current is tested with VIN = VOUT (nominal) and a

current source load. This means that the device is tested while operating

in its dropout region. This is the worst case ground pin current. The

ground pin current will decrease slightly at higher input voltages.

Note 7: Adjust pin bias current flows into the adjust pin.

Note 8: Shutdown pin current at VSHDN = 0V flows out of the shutdown pin.

Note 9: Quiescent current in shutdown is equal to the sum total of the

shutdown pin current (6

µA) and the ground pin current (9µA).

Note 10: Reverse output current is tested with the input pin grounded and

the output pin forced to the rated output voltage. This current flows into

the output pin and out of the ground pin.

The q denotes specifications which apply over the operating temperature

range.

Note 1: The Shutdown pin input voltage rating is required for a low

impedance source. Internal protection devices connected to the shutdown

pin will turn on and clamp the pin to approximately 7V or – 0.6V. This

range allows the use of 5V logic devices to drive the pin directly. For high

impedance sources or logic running on supply voltages greater than 5.5V,

the maximum current driven into the shutdown pin must be limited to less

than 20mA.

Note 2: For junction temperatures greater than 110

°C, a minimum load of

1mA is recommended. For TJ > 110°C and IOUT < 1mA, output voltage

may increase by 1%.

Note 3: Operating conditions are limited by maximum junction

temperature. The regulated output voltage specification will not apply for

all possible combinations of input voltage and output current. When

operating at maximum input voltage, the output current range must be

limited. When operating at maximum output current the input voltage

range must be limited.

LT1121CS8 数据表(PDF) 3 Page - Linear Technology

LT1121CS8 数据表(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载

链接网址

LT1121CS8 数据表(PDF) 3 Page - Linear Technology

LT1121CS8 数据表(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表 下载

链接网址

数据表下载