MAX385CSLASHD datasheet(3/12 Pages) MAXIM

3 / 12 page

Precision, Low-Voltage Analog Switches

_______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)

(V+ = +5V ±10%, V- = -5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)

PARAMETER

SYMBOL

MIN

TYP

MAX

(Note 2)

UNITS

Input Current with Input

Voltage High

IINH

-1.0

0.005

1.0

µA

CONDITIONS

VIN = 2.4V, all others = 0.8V

Input Current with Input

Voltage Low

IINL

-1.0

0.005

1.0

µA

VIN = 0.8V, all others = 2.4V

Turn-On Time

tON

100

175

Charge Injection

(Note 3)

VCTE

CL = 1.0nF, VGEN = 0V,

RGEN = 0Ω, Figure 4

TA = +25°C

TA = TMIN to TMAX

225

VCOM = 3V, Figure 2

TA = +25°C

TA = TMIN to TMAX

150

VCOM = 3V, Figure 2

Turn-Off Time

tOFF

100

Power-Supply Range

MAX383 only, Figure 3

Break-Before-Make

Time Delay (Note 3)

TA = +25°C

RL = 100Ω, CL = 5pF,

f = 1MHz, Figure 5

Off Isolation (Note 6)

VISO

TA = +25°C

RL = 50Ω, CL = 5pF,

f = 1MHz, Figure 6

Crosstalk (Note 7)

VCT

TA = +25°C

f = 1MHz, Figure 7

Off Capacitance

COFF

TA = +25°C

f = 1MHz, Figure 7

COM Off Capacitance

CCOM(OFF)

TA = +25°C

f = 1MHz, Figure 8

Channel On Capacitance CCOM(ON)

±3

±8

Positive Supply Current

I+

All channels on or off,

V+ = 5.5V, V- = -5.5V, VIN = 0V or V+

-1.0

0.06

1.0

µA

Negative Supply

Current

I-

All channels on or off,

V+ = 5.5V, V- = -5.5V, VIN = 0V or V+

-1.0

-0.01

1.0

µA

Logic High Input Voltage

VAH

2.4

Logic Low Input Voltage

VAL

0.8

TA = TMIN to TMAX

Note 2:

The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in

this data sheet.

Note 3:

Guaranteed by design.

Note 4:

∆RON = ∆RON(max) - ∆RON(min). On-resistance match between channels and flatness are guaranteed only with

specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as

measured over the specified analog signal range.

Note 5:

Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temperature.

Note 6:

See Figure 4. Off isolation = 20log10 VCOM/VNC or VNO, VCOM = output, VNC or NO = input to off switch.

Note 7:

Between any two switches. See Figure 5.

Note 8:

Leakage testing at single supply is guaranteed by testing with dual supplies.

TA = +25°C

DIGITAL LOGIC INPUT

SUPPLY

DYNAMIC

MAX385C/D 数据表(PDF) 3 Page - Maxim Integrated Products

MAX385C/D 数据表(HTML) 3 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载

链接网址

MAX385C/D 数据表(PDF) 3 Page - Maxim Integrated Products

MAX385C/D 数据表(HTML) 3 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表 下载

链接网址

数据表下载