Fault-Protected, High-Voltage

Signal-Line Protectors

2

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

(Voltages Referenced to GND)

V+ ........................................................................-0.3V to +44.0V

V- .........................................................................-44.0V to +0.3V

V+ to V-................................................................-0.3V to +44.0V

IN_ or OUT_ .........................................................................±44V

IN_ Overvoltage with Power On...........................................±36V

IN_ Overvoltage with Power Off...........................................±40V

Continuous Current into Any Terminal..............................±30mA

Peak Current into Any Terminal

(pulsed at 1ms, 10% duty cycle).................................±70mA

8-Pin Narrow SO (derate 5.88mW/°C above +70°C) ....471mW

8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) .....727mW

8-Pin CERDIP (derate 8.00mW/°C above +70°C) ...........640mW

18-Pin Wide SO (derate 9.52mW/ °C above +70°C) .......762mW

18-Pin Plastic DIP (derate 11.11mW/ °C above +70°C) ...889mW

18-Pin CERDIP (derate 10.53mW/ °C above +70°C) ......842mW

20-Pin SSOP (derate 11.11mW/°C above +70°C) ...........640mW

Operating Temperature Ranges

MAX4506C_A /MAX4607C_ _ .............................0°C to +70°C

MAX4506E_A/MAX4607E_ _ ...........................-40°C to +85°C

MAX4506MJA/MAX4607MJN ........................-55°C to +125°C

Storage Temperature Range .............................-65°C to +160°C

Lead Temperature (soldering, 10sec) .............................+300°C

RECOMMENDED OPERATING GUIDELINES

V+ to GND ..............................................................-0.3V to +40V

V- to GND ...............................................................-32V to +0.3V

V+ to V- ..................................................................................40V

IN_........................................................................................±40V

OUT_ ...............................................................................V+ to V-

IN_ to OUT_..........................................................40V Differential

Continuous Current into Any Terminal ..............................

≤30mA

Peak Current into Any Terminal

(pulsed at 1ms, 10% duty cycle) .................................

≤70mA

Input Capacitance

pF

20

+25°C

Fault-Protected Analog Signal

Range

V

-36

36

(Notes

2, 3)

C, E, M

Applies with power on

-20

0.1

20

-40

40

nA

C, E, M

-200

200

C, E

+25°C

Applies with power off

Input Signal-Path Leakage

Current, Supplies On

-10

10

65

100

V

V-

V+

Fault-Free Analog Signal Range

(Note 4)

-400

400

Signal-Path Leakage Current

(Note 7)

µA

-20

20

nA

0.5

12

125

Ω

150

Analog Signal-Path Resistance

Ω

17

Signal-Path Resistance Match

(Note 6)

10

UNITS

MIN

TYP

MAX

SYMBOL

PARAMETER

V+ = +15V, V- = -15V,

floating

CONDITIONS

+25°C

C, E, M

M

C, E

+25°C

M

C, E

M

+25°C

C, E

M

ANALOG SWITCH

FAULT PROTECTION

Note 1: OUT_ pins are not fault protected. Signals on OUT_ exceeding V+ or V- are clamped by internal diodes. Limit forward-diode

current to maximum current rating.

Note 2: IN_ pins are fault protected. Signals on IN_ exceeding -36V to +36V may damage the device. These limits apply with power

applied to V+ or V-, or ±40V with V+ = V- = 0.