AM1806 datasheet(24/245 Pages) TI

24 / 245 page

AM1806

SPRS658F – FEBRUARY 2010 – REVISED MARCH 2014

www.ti.com

3.7.6

DDR2/mDDR Memory Controller

Table 3-8. DDR2/mDDR Terminal Functions

SIGNAL

TYPE(1)

PULL(2)

DESCRIPTION

NAME

NO.

DDR_D[15]

W10

I/O

IPD

DDR_D[14]

U11

I/O

IPD

DDR_D[13]

V10

I/O

IPD

DDR_D[12]

U10

I/O

IPD

DDR_D[11]

T12

I/O

IPD

DDR_D[10]

T10

I/O

IPD

DDR_D[9]

T11

I/O

IPD

DDR_D[8]

T13

I/O

IPD

DDR2 SDRAM data bus

DDR_D[7]

W11

I/O

IPD

DDR_D[6]

W12

I/O

IPD

DDR_D[5]

V12

I/O

IPD

DDR_D[4]

V13

I/O

IPD

DDR_D[3]

U13

I/O

IPD

DDR_D[2]

V14

I/O

IPD

DDR_D[1]

U14

I/O

IPD

DDR_D[0]

U15

I/O

IPD

DDR_A[13]

IPD

DDR_A[12]

IPD

DDR_A[11]

IPD

DDR_A[10]

IPD

DDR_A[9]

IPD

DDR_A[8]

IPD

DDR_A[7]

IPD

DDR2 row/column address

DDR_A[6]

IPD

DDR_A[5]

IPD

DDR_A[4]

IPD

DDR_A[3]

IPD

DDR_A[2]

IPD

DDR_A[1]

IPD

DDR_A[0]

IPD

DDR_CLKP

IPD

DDR2 clock (positive)

DDR_CLKN

IPD

DDR2 clock (negative)

DDR_CKE

IPD

DDR2 clock enable

DDR_WE

IPD

DDR2 write enable

DDR_RAS

IPD

DDR2 row address strobe

DDR_CAS

IPD

DDR2 column address strobe

DDR_CS

IPD

DDR2 chip select

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using

the PUPDENA and PUPDSEL registers in the System Module. For more detailed information on pullup/pulldown resistors and situations

where external pullup/pulldown resistors are required, see the Device Configuration section. For electrical specifications on pullup and

internal pulldown circuits, see the Device Operating Conditions section.

Device Overview

Submit Documentation Feedback

Product Folder Links: AM1806

AM1806 数据表(PDF) 24 Page - Texas Instruments

AM1806 数据表(HTML) 24 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载