HCS512-IP datasheet(9/20 Pages) MICROCHIP

9 / 20 page

HCS512

DS40151C-page 9

6.2

Programming the Manufacturer’s

Code

The manufacturer’s code must be programmed into

EEPROM memory through the synchronous program-

ming interface using the DATA and CLK lines. Provision

must be made for connections to these pins if the

decoder is going to be programmed in circuit.

Programming mode is activated if the CLK is low for at

least 1ms and then goes high within 64 ms after power-

up, stays high for longer than 8ms but not longer than

128 ms. After entering programming mode the 64-bit

manufacturer’s code, 8-bit conﬁguration byte, and 8-bit

checksum is sent to the device using the synchronous

interface. After receiving the 80-bit message the check-

sum is veriﬁed and the information is written to

EEPROM. If the programming operation was success-

ful, the HCS512 will respond with an acknowledge

pulse.

After programming the manufacturer’s code, the

HCS512

decoder

will

automatically

activate

Erase All function, removing all transmitters from the

system.

6.3

Download Format

The manufacturer’s code and conﬁguration byte must

be downloaded least signiﬁcant byte, least signiﬁcant

bit ﬁrst as shown in Table 6-3.

6.4

Checksum

The checksum is used by the HCS512 to check that the

data downloaded was correctly received before pro-

gramming the data. The checksum is calculated so that

the 10 bytes added together (discarding the overﬂow

bits) is zero. The checksum can be calculated by adding

the ﬁrst 9 bytes of data together and subtracting the

result from zero. Throughout the calculation the over-

ﬂow is discarded.

Given

manufacturer’s

code

01234567-

89ABCDEF16 and a conﬁguration word of 116, the

checksum is calculated as shown in Figure 6-1. The

checksum is 3F16.

6.5

Test Transmitter

The HCS512 decoder will automatically add a test

transmitter each time an Erase All Function is done. A

test transmitter is deﬁned as a transmitter with a serial

number of zero. After an Erase All, the test transmitter

will always work without learning and will not check the

synchronization counter of the transmitter. Learning of

any new transmitters will erase the test transmitter.

TABLE 6-3:

DOWNLOAD DATA

FIGURE 6-1:

CHECKSUM CALCULATION

Note 1: A transmitter with a serial number of zero

cannot be learned. Learn will fail after the

ﬁrst transmission.

2: Always learn at least one transmitter after

an Erase All sequence. This ensures that

the test transmitter is erased.

Byte 9

Byte 8

Byte 7

Byte 6

Byte 5

Byte 4

Byte 3

Byte 2

Byte 1

Byte 0

Check-

sum

Conﬁg

Man

Key_7

Man

Key_6

Man

Key_5

Man

Key_4

Man

Key_3

Man

Key_2

Man

Key_1

Man

Key_0

Byte 0, right-most bit downloaded ﬁrst.

0116 + 2316 = 246

2416 + 4516 = 6916

6916 + 6716 = D016

D016 + 8916 = 15916

5916 + AB16 = 10416 (Carry is discarded)

0416 + CD16 = D116 (Carry is discarded)

D116 + EF16 = 1C016

C016 + 116 = C116 (Carry is discarded)

(FF16 - C116) + 116 = 3F16

HCS512-IP 数据表(PDF) 9 Page - Microchip Technology

HCS512-IP 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表下载