PIC16LC712 datasheet(21/108 Pages) MICROCHIP

21 / 108 page

Preliminary

DS41106A-page 21

PIC16C712/716

3.0

I/O PORTS

Some pins for these I/O ports are multiplexed with an

alternate function for the peripheral features on the

device. In general, when a peripheral is enabled, that

pin may not be used as a general purpose I/O pin.

Additional information on I/O ports may be found in the

PICmicro™

Mid-Range

Reference

Manual,

(DS33023).

3.1

PORTA and the TRISA Register

PORTA is a 5-bit wide bi-directional port. The corre-

sponding data direction register is TRISA. Setting a

TRISA bit (=1) will make the corresponding PORTA pin

an input, (i.e., put the corresponding output driver in a

hi-impedance mode). Clearing a TRISA bit (=0) will

make the corresponding PORTA pin an output, (i.e., put

the contents of the output latch on the selected pin).

Reading the PORTA register reads the status of the

pins whereas writing to it will write to the port latch. All

write operations are read-modify-write operations.

Therefore a write to a port implies that the port pins are

read, the value is modified, and then written to the port

data latch.

Pin RA4 is multiplexed with the Timer0 module clock

input to become the RA4/T0CKI pin. The RA4/T0CKI

pin is a Schmitt Trigger input and an open drain output.

All other RA port pins have TTL input levels and full

CMOS output drivers.

PORTA pins, RA3:0, are multiplexed with analog inputs

and analog VREF input. The operation of each pin is

selected by clearing/setting the control bits in the

ADCON1 register (A/D Control Register1).

The TRISA register controls the direction of the RA

pins, even when they are being used as analog inputs.

The user must ensure the bits in the TRISA register are

maintained set when using them as analog inputs.

EXAMPLE 3-1:

INITIALIZING PORTA

BCF

STATUS, RP0

;

CLRF

PORTA

; Initialize PORTA by

; clearing output

; data latches

BSF

STATUS, RP0

; Select Bank 1

MOVLW

0xEF

; Value used to

; initialize data

; direction

MOVWF

TRISA

; Set RA<3:0> as inputs

; RA<4> as outputs

BCF

STATUS, RP0

; Return to Bank 0

Note:

On a Power-on Reset, these pins are con-

figured as analog inputs and read as '0'.

FIGURE 3-1:

BLOCK DIAGRAM OF RA3:RA0

DATA

BUS

PORT

TRIS

Data Latch

TRIS Latch

RD TRIS

RD PORT

VSS

VDD

I/O pin

Analog

input

mode

TTL

Input

Buffer

To A/D Converter

VSS

VDD

PIC16LC712 数据表(PDF) 21 Page - Microchip Technology

PIC16LC712 数据表(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC16LC712 数据表(PDF) 21 Page - Microchip Technology

PIC16LC712 数据表(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载