PIC16F628-20SLASHSS datasheet(44/160 Pages) MICROCHIP

44 / 160 page

PIC16F62X

DS40300B-page 44

Preliminary

5.3

I/O Programming Considerations

5.3.1

BI-DIRECTIONAL I/O PORTS

Any instruction which writes, operates internally as a

read followed by a write operation. The BCF and BSF

instructions, for example, read the register into the

CPU, execute the bit operation and write the result back

to the register. Caution must be used when these

instructions are applied to a port with both inputs and

outputs defined. For example, a BSF operation on bit5

of PORTB will cause all eight bits of PORTB to be read

into the CPU. Then the BSF operation takes place on

bit5 and PORTB is written to the output latches. If

another bit of PORTB is used as a bidirectional I/O pin

(e.g., bit0) and it is defined as an input at this time, the

input signal present on the pin itself would be read into

the CPU and re-written to the data latch of this

particular pin, overwriting the previous content. As long

as the pin stays in the input mode, no problem occurs.

However, if bit0 is switched into output mode later on,

the content of the data latch may now be unknown.

Reading a port register, reads the values of the port

pins. Writing to the port register writes the value to the

port latch. When using read modify write instructions

(ex. BCF, BSF, etc.) on a port, the value of the port pins

is read, the desired operation is done to this value, and

this value is then written to the port latch.

Example 5-2 shows the effect of two sequential

read-modify-write instructions (ex., BCF, BSF, etc.) on

an I/O port.

A pin actively outputting a Low or High should not be

driven from external devices at the same time in order

to change the level on this pin (“wired-or”, “wired-and”).

The resulting high output currents may damage

the chip.

EXAMPLE 5-2:

READ-MODIFY-WRITE

INSTRUCTIONS ON AN

I/O PORT

5.3.2

SUCCESSIVE OPERATIONS ON I/O PORTS

The actual write to an I/O port happens at the end of an

instruction cycle, whereas for reading, the data must be

valid at the beginning of the instruction cycle

(Figure 5-16). Therefore, care must be exercised if a

write followed by a read operation is carried out on the

same I/O port. The sequence of instructions should be

such to allow the pin voltage to stabilize (load

dependent) before the next instruction which causes

that file to be read into the CPU is executed. Otherwise,

the previous state of that pin may be read into the CPU

rather than the new state. When in doubt, it is better to

separate these instructions with a NOP or another

instruction not accessing this I/O port.

;

Initial PORT settings:

PORTB<7:4> Inputs

;

PORTB<3:0> Outputs

;

PORTB<7:6> have external pull-up and are not

connected to other circuitry

;

PORT latch

PORT pins

;

----------

BDF STATUS,RPO

;

BCF PORTB, 7

; 01pp pppp

11pp pppp

BCF PORTB, 6

; 10pp pppp

11pp pppp

BSF STATUS,RP0

;

BCF TRISB, 7

; 10pp pppp

11pp pppp

BCF TRISB, 6

; 10pp pppp

10pp pppp

;

; Note that the user may have expected the pin

; values to be 00pp pppp. The 2nd BCF caused

; RB7 to be latched as the pin value (High).

FIGURE 5-16: SUCCESSIVE I/O OPERATION

Note:

This example shows write to PORTB

followed by a read from PORTB.

Note that:

data setup time = (0.25 TCY - TPD)

where TCY = instruction cycle and

TPD = propagation delay of Q1 cycle

to output valid.

Therefore, at higher clock frequencies,

a write followed by a read may be

problematic.

RB <7:0>

Port pin

sampled here

PC + 1

PC + 2

PC + 3

NOP

MOVF PORTB, W

Read PORTB

MOVWF PORTB

Write to

PORTB

Instruction

fetched

T PD

Execute

MOVWF

PORTB

Execute

MOVF

PORTB, W

Execute

NOP

RB<7:0>

Instruction

fetched

MOWF PORTB

Write to PORTB

MOVF PORTB, W

Read to PORTB

NOP

Execute

MOVWF

PORTB

Execute

MOVWF

PORTB

Execute

NOP

TPD

Port pin

sampled here

PC + 1

PC + 2

PC + 3

PIC16F628-20/SS 数据表(PDF) 44 Page - Microchip Technology

PIC16F628-20/SS 数据表(HTML) 44 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC16F628-20/SS 数据表(PDF) 44 Page - Microchip Technology

PIC16F628-20/SS 数据表(HTML) 44 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载