LAN9730 datasheet(21/222 Pages) MICROCHIP

21 / 222 page

 2012-2015 Microchip Technology Inc.

DS00001946A-page 21

LAN9730/LAN9730i

Ethernet Link

Activity Indi-

cator LED

nLNKA_LED

OD12

(PU)

This pin is driven low (LED on) when a valid link is

detected. This pin is pulsed high (LED off) for

80 ms whenever transmit or receive activity is

detected. This pin is then driven low again for a

minimum of 80 ms, after which time it will repeat

the process if TX or RX activity is detected. Effec-

tively, LED2 is activated solid for a link. When

transmit or receive activity is sensed, LED2 will

function as an activity indicator.

General Pur-

pose I/O 9

GPIO9

IS/O12/

OD12

(PU)

This General Purpose I/O pin is fully programma-

ble as either a push-pull output, an open-drain

output or a Schmitt-triggered input.

Note:

This pin may serve as the

PME_MODE_SEL input when External

PHY and PME Modes of operation are

in effect. Refer to Chapter 5.0, "PME

Operation" for additional information.

Note:

By default this pin is configured as a

GPIO.

Ethernet

Speed Indica-

tor LED

nSPD_LED

OD12

(PU)

This pin is driven low (LED on) when the Ethernet

operating speed is 100 Mbs, or during auto-nego-

tiation. This pin is driven high during 10 Mbs oper-

ation or during line isolation.

General Pur-

pose I/O 10

GPIO10

IS/O12/

OD12

(PU)

This General Purpose I/O pin is fully programma-

ble as either a push-pull output, an open-drain

output or a Schmitt-triggered input.

Note:

This pin may serve as a wakeup pin

whose detection mode is selectable

when External PHY and PME Modes of

operation are in effect. Refer to Chapter

5.0, "PME Operation" for additional

information.

Note:

By default this pin is configured as a

GPIO.

Core Regula-

tor Enable

CORE_REG_EN

This pin enables/disables the internal core logic

voltage regulator.

When tied low to VSS, the internal core regulator

is disabled and +1.2 V must be supplied to the

device by an external source.

When tied high to +3.3 V, the internal core regula-

tor is enabled.

Refer to Chapter 3.0, "Power Connections" and

the device reference schematics for connection

information.

Test 1

TEST1

This pin must always be connected to VSS for

proper operation.

TABLE 2-4:

MISCELLANEOUS PINS (CONTINUED)

Num Pins

Name

Symbol

Buffer

Type

Description

LAN9730 数据表(PDF) 21 Page - Microchip Technology

LAN9730 数据表(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

LAN9730 数据表(PDF) 21 Page - Microchip Technology

LAN9730 数据表(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载